Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

4020 Hard Starting Update 2


 
Post new topic    
View previous topic :: View next topic  
Author Message
2510Paul
Long Time User


Joined: 27 Nov 2007
Posts: 1273
Location: La Crosse, WI

Report to Moderator

PostPosted: Fri Jan 12, 2018 4:51 pm    Post subject: 4020 Hard Starting Update 2 Reply to specific post Reply with quote

Regarding the 4020 hard starting the owner has consented to putting in a remanufactured Delco-Remy starter from JD. The one I need is in their spring sale starting February 1. We'll put in the starter and then decide what to do with the batteries.

Regarding the steering issues:

1. Re-call I ran an air test that failed. The Steering Motor test passed.

2. I found the bleed valve, first picture, on the Steering Motor. It was so covered in oily dirt it was a little hard to find.

3. I connected a clear hose and routed it to the Hydraulic Level Check tube, second picture. I lifted the front of the tractor to make the steering easier and ran the air bleed procedure. I really cannot tell you what I saw in air. When I started the test the front wheels acted very erratically and I was paying attention to that. As I ran the procedure they synchronized and operated as expected.

3a. I removed the bleed valve and cleaned it and the area around. It had a spring and ball bearing in it. The parts book does not show a spring. I don't know what that is all about. I put it all back together and tightened it along with the locking nut. As I did this it occurred to me the bleed valve may have not been tight, pretty sure it wasn't which would explain all the oil and dirt around it.

3b. I took the tractor for a two mile ride, it was 40 F that day, the steering seemed to work OK to me. It took very little steering movement to effect change.

3c. The owner came and drove the tractor the next day, again 40 F that day. He gave me a big thumbs up. I think he had fun on such a nice day. He must of went about 5 miles. He is 77.

4. When I lifted the front tractor I noticed the front wheel bearings and vertical knee bushings were very loose. So that is the third picture, ready to be dis-assembled.

So, it seems that either there was air in the system or the bleed valve was leaking or both. Fingers crossed but it steers fine now and tightening the wheel bearing and replacing the bushings will be icing on the cake.

So that is what I have today. Again, thanks for all your comments and help. I'll post again after I get the remanufactured starter in.

Ya, the squirrels and rodents had a bunch of nuts and debris under the platform I have to clean up.

Stay warm, wind chills are expected to be in the -30's again tomorrow.

Paul



 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters