Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

JD Seller major NH276 Pickup repair


 
Post new topic    
View previous topic :: View next topic  
Author Message
Hay hay hay
Tractor Expert


Joined: 02 Mar 2012
Posts: 2820
Location: Bluegrass region

Report to Moderator

PostPosted: Sun Feb 04, 2018 1:29 pm    Post subject: JD Seller major NH276 Pickup repair Reply to specific post Reply with quote

I need to replace the cam track in a NH 276 baler supersweep pickup assembly.

My question what is the best way to pull the whole pickup assembly out of the baler?
It appears that the assembly is held in place by the drive shaft. Will the bearings come out with the shaft or will I need to heat it and drive the shaft thru the bearings? I have not started pulling it apart yet so any tips and insights will be appreciated. Nothing in the manual covers this assembly removal.

Anyone with experience please chime in.
 
Back to top
View user's profile
shaun wallace
Tractor Expert


Joined: 11 May 2008
Posts: 2896


Report to Moderator

PostPosted: Sun Feb 04, 2018 3:02 pm    Post subject: Re: JD Seller major NH276 Pickup repair Reply to specific post Reply with quote

No donot have to pull pickup off. Take couple end bows off,remove rollers from tooth bars, See cutout in track and slide out over shaft.
 
Back to top
View user's profile
Hay hay hay
Tractor Expert


Joined: 02 Mar 2012
Posts: 2820
Location: Bluegrass region

Report to Moderator

PostPosted: Sun Feb 04, 2018 3:16 pm    Post subject: Re: JD Seller major NH276 Pickup repair Reply to specific post Reply with quote

You made my day...you are sure the opening in the track is large enough to allow it to slide out past the center shaft? Thanks
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters