Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Inner Shoe Wear Plate


 
Post new topic    
View previous topic :: View next topic  
Author Message
Briar Hill Brittanys
Long Time User


Joined: 14 May 2009
Posts: 1133
Location: Jasper, MO

Report to Moderator

PostPosted: Mon Mar 12, 2018 5:08 am    Post subject: Inner Shoe Wear Plate Reply to specific post Reply with quote

To keep from hijacking SVcummins post on Haymowers, I posted this. I'm refurbbing my JD #9W mower. When reassembling the inner shoe, I discovered a missing wear plate on the inner shoe, under the front guide. I have a #9 mower for spare parts, and the plate was missing from it as well. Part number H24379 is still available from JD, price is $30.93. Wondering if anyone knew the thickness? I could probably make quite a few for $31.
 
Back to top
View user's profile
DeltaRed
Tractor Guru


Joined: 25 Feb 2010
Posts: 14506
Location: Delta,colorado

Report to Moderator

PostPosted: Mon Mar 12, 2018 5:29 am    Post subject: Re: Inner Shoe Wear Plate Reply to specific post Reply with quote

1/4" or 3/8.I think $31 would be cheap compared to all the labor involed. It's more than just a flat chunk of steel with a couple of holes.
 
Back to top
View user's profile
carvel minne farmer
Tractor Expert


Joined: 13 Aug 2017
Posts: 1756
Location: carvel alberta canada

Report to Moderator

PostPosted: Mon Mar 12, 2018 6:55 am    Post subject: Re: Inner Shoe Wear Plate Reply to specific post Reply with quote

briar I just built one out of 1/4" plate for my ih-100 that was missing.
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 76627
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Mon Mar 12, 2018 8:08 am    Post subject: Re: Inner Shoe Wear Plate Reply to specific post Reply with quote

Well if it wasn't buried in a black berry thicket I could go out and measure the one on my JD #9. But I have not used it since I let a friend use it and he lost the inner pitman arm mount
 
Back to top
View user's profile
rrlund
Tractor Guru


Joined: 21 Dec 2006
Posts: 38193


Report to Moderator

PostPosted: Mon Mar 12, 2018 10:58 am    Post subject: Re: Inner Shoe Wear Plate Reply to specific post Reply with quote

If you're just using ordinary cold roll,you'll be making a lot of them. They won't be hard enough and will wear out pretty quick.
 
Back to top
View user's profile
donjr
Tractor Guru


Joined: 20 Nov 2011
Posts: 8724


Report to Moderator

PostPosted: Mon Mar 12, 2018 4:52 pm    Post subject: Re: Inner Shoe Wear Plate Reply to specific post Reply with quote

When I wearer one out, I use a hunk of truck spring to build a new one. They wear for a LONG time.....
 
Back to top
View user's profile
Briar Hill Brittanys
Long Time User


Joined: 14 May 2009
Posts: 1133
Location: Jasper, MO

Report to Moderator

PostPosted: Mon Mar 12, 2018 7:15 pm    Post subject: Re: Inner Shoe Wear Plate Reply to specific post Reply with quote

Appreciate the replies. Thought they could be made from some 1/4" diamond plate. The mower probably only sees 12 acres a year, would they wear out that fast? I believe it's been missing for the 4 years I've owned the mower.
 
Back to top
View user's profile
SVcummins
Tractor Guru


Joined: 06 Feb 2017
Posts: 3820


Report to Moderator

PostPosted: Mon Mar 12, 2018 7:48 pm    Post subject: Re: Inner Shoe Wear Plate Reply to specific post Reply with quote

I just looked at an aftermarket for my mower and it I 70$ so the John Deere part is a better deal
 
Back to top
View user's profile
SVcummins
Tractor Guru


Joined: 06 Feb 2017
Posts: 3820


Report to Moderator

PostPosted: Wed Mar 14, 2018 11:52 am    Post subject: Re: Inner Shoe Wear Plate Reply to specific post Reply with quote

The worst you can do is try it if it don?t last like you
think it should you can always buy one . I probably
wouldn?t use diamond plate because it?s kinda hard
to work with
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters