Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Clutch will not disengage ?49 cub


 
Post new topic    
View previous topic :: View next topic  
Author Message
Don Hanvey
Regular


Joined: 07 Aug 2011
Posts: 52


Report to Moderator

PostPosted: Thu Jun 14, 2018 8:21 am    Post subject: Clutch will not disengage ?49 cub Reply to specific post Reply with quote

Installed new clutch disk, pressure plate, pilot bushing and throw out bearing.
Clutch will not disengage. I adjusted the pressure plate fingers but I guess it is wrong. How do u properly adjust the fingers before installation?
 
Back to top
View user's profile
ih560
Long Time User


Joined: 27 Sep 2007
Posts: 513


Report to Moderator

PostPosted: Thu Jun 14, 2018 3:14 pm    Post subject: Re: Clutch will not disengage ?49 cub Reply to specific post Reply with quote

With the clutch and pressure plate installed on the flywheel, adjust the fingers so that it measures 1-1/4" from face of pressure plate to where the throw out bearing contacts the fingers.
 
Back to top
View user's profile
BarnyardEngineering
Tractor Guru


Joined: 23 Mar 2016
Posts: 3641


Report to Moderator

PostPosted: Fri Jun 15, 2018 3:36 am    Post subject: Re: Clutch will not disengage ?49 cub Reply to specific post Reply with quote

The new pressure plates don't have bolts long enough for 1-1/4". You can barely get 1-1/8" and still have enough thread for the lock nut to engage.

1-1/8" does work and is the new measurement for these fingers.

Another possibility is that you put the clutch disk in backwards.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters