Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1012 bale wagon cylinder


 
Post new topic    
View previous topic :: View next topic  
Author Message
MSS3020
Long Time User


Joined: 19 Mar 2002
Posts: 1407
Location: Firth, Nebraska

Report to Moderator

PostPosted: Thu Jun 14, 2018 6:30 am    Post subject: 1012 bale wagon cylinder Reply to specific post Reply with quote

I have done a few cylinders in my time enough that I bought a spanner wrench.. had to replace the seals in it. Had a what I call C type wire clamp about 1/4 down inside between outside cylinder wall and inner steel type thing.. Turns out you have to drive the inner steel thingy down about 1/2 inch to expose the wire C. then you can pick the C out and pull/drive the rest of the ram and guts out.. OH hand drive the inner piece without damage as it excepts a seal that the ram runs through.. Got er done but rather work on spanner type.. good experience to know though..

So is that old technology when they made these or??
 
Back to top
View user's profile
Bob
Tractor Guru


Joined: 03 Jan 1998
Posts: 50865


Report to Moderator

PostPosted: Thu Jun 14, 2018 9:42 pm    Post subject: Re: 1012 bale wagon cylinder Reply to specific post Reply with quote

"So is that old technology when they made these or??"

Dunno, how OLD it was at that time, but COMMON.

Did the reseal fix your "spitting oil" problem?

Now that you have experience, how about coming over and helping me with a similar project an the lift cylinder from a LARGE Westfield auger?
 
Back to top
View user's profile
MSS3020
Long Time User


Joined: 19 Mar 2002
Posts: 1407
Location: Firth, Nebraska

Report to Moderator

PostPosted: Fri Jun 15, 2018 5:44 am    Post subject: Re: 1012 bale wagon cylinder Reply to specific post Reply with quote

It did fix the problem.. thanks for the info on original question.. If you lived near I wouldnt mind helping ya out..Its always easier after one learns how to do it..sometimes anyway...

1012 getting that cylinder out was interesting.. Unless I miss something there but I had to release the "garage door type return springs" push the push out feed to relieve the cable, pull the second table pin and pushed cylinder backward to the rear and remove that pin.. Someone used a torch and cut a hole about 2 feet back in the wall where those cable slides/cylinder slides in so you can remove the pin.. didnt look like a factory hole to me anyway..
Trying to line up the pin through the cable slide to the cylinder to the other side cable slide and the lock latch was interesting in its self.. but got er done and ready to rock and roll this weekend..

THANKS for your help.. learning experience last year with this wagon... this year plan to use the stuffing out of it..
 
Back to top
View user's profile
Bob
Tractor Guru


Joined: 03 Jan 1998
Posts: 50865


Report to Moderator

PostPosted: Fri Jun 15, 2018 8:44 am    Post subject: Re: 1012 bale wagon cylinder Reply to specific post Reply with quote

When they they work as intended they are a lot of fun to run.
 
Back to top
View user's profile
SVcummins
Tractor Guru


Joined: 06 Feb 2017
Posts: 4377


Report to Moderator

PostPosted: Fri Jun 15, 2018 7:07 pm    Post subject: Re: 1012 bale wagon cylinder Reply to specific post Reply with quote

Those kind aren?t bad until the wire breaks off inside because it?s so old and corroded
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters