View previous topic :: View next topic |
Author |
Message |
brumik Regular
Joined: 22 Feb 2010 Posts: 29
Report to Moderator
|
Posted: Sun Apr 03, 2011 6:14 am Post subject: Farmall super c - cam gear governor gear timing que... |
|
|
I replaced a bad Cam Gear on my super c.
I've got the punch marks meshed up on the crank and cam gears.
Do i need to also do the same with the governor gear?
I actually don"t think the governor gear was in mesh with tick mars when i took it apart. I think it was about one third way around the gear approximately.
I've got a 12 volt system with distributor - if this matters at all.
Any advice is appreciated.
Bruce |
|
Back to top |
|
 |
rustred Tractor Guru
Joined: 01 Jul 2009 Posts: 6537
Report to Moderator
|
Posted: Sun Apr 03, 2011 7:29 am Post subject: Re: Farmall super c - cam gear governor gear timing que... |
|
|
no timing required on governor gear. |
|
Back to top |
|
 |
teddy52food Tractor Guru
Joined: 05 Mar 2006 Posts: 8520
Report to Moderator
|
Posted: Sun Apr 03, 2011 7:51 am Post subject: Re: Farmall super c - cam gear governor gear timing que... |
|
|
Why not put it in time? If you ever want to put a mag on, you will have fun. |
|
Back to top |
|
 |
rustred Tractor Guru
Joined: 01 Jul 2009 Posts: 6537
Report to Moderator
|
Posted: Sun Apr 03, 2011 9:49 am Post subject: Re: Farmall super c - cam gear governor gear timing que... |
|
|
correction: yes distributer and governor gear is timed as its the same gear on the C . was thinking about the H series where the governor gear is on the left side and timing is not nessesary of the governor gear. |
|
Back to top |
|
 |
brumik Regular
Joined: 22 Feb 2010 Posts: 29
Report to Moderator
|
Posted: Sun Apr 03, 2011 10:29 am Post subject: Re: Farmall super c - cam gear governor gear timing que... |
|
|
Thanks - but, are you saying if it runs off distributor it doesn't need to be timed?
Bruce |
|
Back to top |
|
 |
brumik Regular
Joined: 22 Feb 2010 Posts: 29
Report to Moderator
|
Posted: Sun Apr 03, 2011 10:33 am Post subject: Re: Farmall super c - cam gear governor gear timing que... |
|
|
What's funny rusty is - i've been told both ---- that it must be timed, and that no, the C doesn't need to be timed.
I'm just pretty sure that the governor gear wasn't meshed with the punch mark, and it ran nice. But i'm not 100% certain about the mark.
I just hate to do it one way, and have to take the damn thing apart again. |
|
Back to top |
|
 |
rustred Tractor Guru
Joined: 01 Jul 2009 Posts: 6537
Report to Moderator
|
Posted: Sun Apr 03, 2011 11:21 am Post subject: Re: Farmall super c - cam gear governor gear timing que... |
|
|
you can get away without timing the dist.gear. best to line them up since once you have the cam and crank timed the other mark on the cam gear is in position to time with the dist gear.just requires installing the dist gear mark to the mark on cam. |
|
Back to top |
|
 |
brumik Regular
Joined: 22 Feb 2010 Posts: 29
Report to Moderator
|
Posted: Mon Apr 04, 2011 1:07 am Post subject: Re: Farmall super c - cam gear governor gear timing que... |
|
|
Thanks - i will time the governor - i just wasn't sure how important it was. |
|
Back to top |
|
 |
poss0311 New User
Joined: 17 Jan 2013 Posts: 1
Report to Moderator
|
Posted: Thu Jan 17, 2013 6:35 pm Post subject: Re: Farmall super c - cam gear governor gear timing que... |
|
|
Quick question the Cam Gear has 2 sets of punch marks one double and one single. The double punch mark meets to the crank? |
|
Back to top |
|
 |
|