Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

oil pickup tube came out of pump


 
Post new topic    
View previous topic :: View next topic  
Author Message
chris laube
Regular


Joined: 13 Nov 2011
Posts: 86


Report to Moderator

PostPosted: Sun Nov 13, 2011 5:25 pm    Post subject: oil pickup tube came out of pump Reply to specific post Reply with quote

my oil pickup tube came out of the pump housing,looks like it was soldered.How can i reattach the tube.
 
Back to top
View user's profile
Lumpy
Long Time User


Joined: 22 Mar 2009
Posts: 1004


Report to Moderator

PostPosted: Sun Nov 13, 2011 5:45 pm    Post subject: Re: oil pickup tube came out of pump Reply to specific post Reply with quote

They are ALL silver soldered. Find someone who can re-solder it for you.
 
Back to top
View user's profile
chris laube
Regular


Joined: 13 Nov 2011
Posts: 86


Report to Moderator

PostPosted: Sun Nov 13, 2011 5:52 pm    Post subject: Re: oil pickup tube came out of pump Reply to specific post Reply with quote

i have soldered alot of copper,im a plumber but never steel,would i be able to do it myself
 
Back to top
View user's profile
TheOldHokie
Tractor Guru


Joined: 08 Apr 2005
Posts: 7102
Location: Myersville, MD

Report to Moderator

PostPosted: Sun Nov 13, 2011 6:05 pm    Post subject: Re: oil pickup tube came out of pump Reply to specific post Reply with quote

chris laube wrote:
(quoted from post at 21:52:07 11/13/11) i have soldered alot of copper,im a plumber but never steel,would i be able to do it myself


Yes - it's nothing more than tubing in a heavy steel fitting - brazed or silver solder preferred for strength. Get it sqeeky clean and use your acetylene torch to get the heat required.

TOH
 
Back to top
View user's profile Visit poster's website
Hobo,NC
Tractor Guru


Joined: 14 Jun 2007
Posts: 12244


Report to Moderator

PostPosted: Sun Nov 13, 2011 6:28 pm    Post subject: Re: oil pickup tube came out of pump Reply to specific post Reply with quote

chris laube wrote:
(quoted from post at 02:25:27 11/14/11) my oil pickup tube came out of the pump housing,looks like it was soldered.How can i reattach the tube.


Originally they were lead soldered,,, I go back with silver,,, gotta B extra clean,,, it takes a ox/acetylene set up to get'er done....

Remove the front maine cap,,, clamp it to a level surface,,, use a square to square up the big end of the tube,,, Have at it...
 
Back to top
View user's profile
chris laube
Regular


Joined: 13 Nov 2011
Posts: 86


Report to Moderator

PostPosted: Mon Nov 14, 2011 4:37 pm    Post subject: Re: oil pickup tube came out of pump Reply to specific post Reply with quote


can i use a mapp gas tank,do i use flux just like with copper pipe,how much does magnaflux cost for a block do they clean everything also.There was wire twisted on the crank shaft bearings is this hard to do,is there an alternative.
thanks alot for advise
 
Back to top
View user's profile
Hobo,NC
Tractor Guru


Joined: 14 Jun 2007
Posts: 12244


Report to Moderator

PostPosted: Tue Nov 15, 2011 4:08 am    Post subject: Re: oil pickup tube came out of pump Reply to specific post Reply with quote

chris laube wrote:
(quoted from post at 01:37:48 11/15/11)
can i use a mapp gas tank,do i use flux just like with copper pipe,how much does magnaflux cost for a block do they clean everything also.There was wire twisted on the crank shaft bearings is this hard to do,is there an alternative.
thanks alot for advise


mapp gas, NO,,, if you are looking to dob it up and make a mess. YES...
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters