|
This is the modern view of the Yesterday's Tractors Forums. Just login with your YT Userid and password to post. If you have trouble logging in, contact us by email to support at ytmag.com, or through the Reader Form, and we will get you going right away.
| View previous topic :: View next topic |
| Author |
Message |
davdi
New User
Joined: 31 Mar 2012
Posts: 1
Report to Moderator
|
 Posted: Sat Mar 31, 2012 1:32 pm Post subject: hauling a combine |
  |
|
How is the best way to haul a model 60 all crop on a trailer?
|
|
| Back to top |
|
 |
Ralph Bauer
Tractor Expert
Joined: 10 May 2011
Posts: 1555
Location: Greer County, Oklahoma
Report to Moderator
|
| Posted: Sat Mar 31, 2012 6:14 pm Post subject: Re: hauling a combine |
|
|
Look at the post "A/C AllCrop 72", posted around 3-16-12 in the implement forum. Got some good feedback that can be helpful to you.
Quick recap: Most likely you got brass bushings, prone to overheat when towing. grease them well before you leave and about every 5 miles thereafter, low speed, about 15 mph. So pack plenty of grease and time to get there....
If you have to load it, check with Tom Yaz at allcropharvester.com (I think I got the address right) he can tell you how to do it best.
Hope all the posts in the implement forum help, too. Good luck and keep us posted. Ralph in Oklahoma.
|
|
| Back to top |
|
|
JMS/.MN
Tractor Guru
Joined: 05 Mar 2009
Posts: 5896
Report to Moderator
|
| Posted: Fri Apr 06, 2012 9:27 pm Post subject: Re: hauling a combine |
|
|
I have a 66 with two row corn head. My trailer was 102 wide, but too narrow for the 66, (same as your 60) so I built a temporary outrigger on the right side, to match the wheel width. Temp ramp as well. Backed the combine on, Heavy CH is over outrigger. Bouncing created leverage by the outrigger on the trailer frame and cracked some frame welds. Next time I"ll back it on, then jack up that side and support it with blocking down to the main deck, no weight on the outrigger. Previously I towed it to shows- grease every 5-7 miles, limit to 15 mph. Wheels have only brass bushings, no real bearing.
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
|
|
Discount Prices for Parts! You can help support this extensive website by purchasing your tractor parts, manuals and merchandise from our [ Antique Tractor Store ] or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
|
YT Home
| Tractor Manuals
| Tractor Parts
| Forum Home
Copyright © 1997-2013 Yesterday's Tractor Co. - A Washington State Corporation
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
