Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

calling Dick L


 
Post new topic    
View previous topic :: View next topic  
Author Message
OldMoIron
Regular


Joined: 12 Jan 2010
Posts: 176


Report to Moderator

PostPosted: Fri Aug 03, 2012 7:16 pm    Post subject: calling Dick L Reply to specific post Reply with quote

I seen were you had posted some pictures of a drawbar on a C. I was wondering if you had some pictures of some tip over bars you could post, thanks
 
Back to top
View user's profile
Dick L
Tractor Guru


Joined: 01 Sep 1999
Posts: 9724
Location: Edon Ohio

Report to Moderator

PostPosted: Sat Aug 04, 2012 4:51 am    Post subject: Re: calling Dick L Reply to specific post Reply with quote

I made my (chicken bars)one evening using scraps I had laying around when I found out I needed them for a pull the next day. I used the cultivator brackets on top and the plow brackets below. The picture I posted of the drawbar is the best one I have in my picture album as far as I remember. I will look for a better picture.
 
Back to top
View user's profile
Dick L
Tractor Guru


Joined: 01 Sep 1999
Posts: 9724
Location: Edon Ohio

Report to Moderator

PostPosted: Sat Aug 04, 2012 5:05 am    Post subject: Here Be Some Pix Reply to specific post Reply with quote








 
Back to top
View user's profile
OldMoIron
Regular


Joined: 12 Jan 2010
Posts: 176


Report to Moderator

PostPosted: Sat Aug 04, 2012 7:17 am    Post subject: Re: calling Dick L Reply to specific post Reply with quote

thanks for your time to do that, sometimes just need little something get your mind going. Im going to try to build some for a CA
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters