Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

F40 Ring Gear


 
Post new topic    
View previous topic :: View next topic  
Author Message
miner09
Long Time User


Joined: 02 Dec 2009
Posts: 1360


Report to Moderator

PostPosted: Sat Aug 04, 2012 6:05 pm    Post subject: F40 Ring Gear Reply to specific post Reply with quote

Is the ring gear on a High-Crop the same as a Utility? The numbers on casting of housing is the same, but I didn't know if the ring gear is different for the larger tires.
 
Back to top
View user's profile
Richard L
Tractor Expert


Joined: 04 Nov 2007
Posts: 3121


Report to Moderator

PostPosted: Sat Aug 04, 2012 6:12 pm    Post subject: Re: F40 Ring Gear Reply to specific post Reply with quote

If you are talking about the starter ring gear the parts book only shows one number 1 750 034 M1 Gear, Starter Ring.
 
Back to top
View user's profile
miner09
Long Time User


Joined: 02 Dec 2009
Posts: 1360


Report to Moderator

PostPosted: Sun Aug 05, 2012 2:46 am    Post subject: Re: F40 Ring Gear Reply to specific post Reply with quote

Sorry, I was asking about ring gear and pinion. I bought a utility tractor with a busted rear housing. I have a good high crop rear end, but didn't know if they were different. I'll use two to make one tractor.
 
Back to top
View user's profile
Richard L
Tractor Expert


Joined: 04 Nov 2007
Posts: 3121


Report to Moderator

PostPosted: Sun Aug 05, 2012 5:14 am    Post subject: Re: F40 Ring Gear Reply to specific post Reply with quote

The parts book shows: 182 089 M1 Gear, Ring (37 Teeth) (Order 82 115 M91) which this 2nd number refers to the "Mated Gear Set". I am sure there are different tachometers for the HI and the Utility but as far as the ring and pinion I do not know. I believe Paul in AZ will let you know if he is around today.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters