Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

oliver 129 haybine


 
Post new topic    
View previous topic :: View next topic  
Author Message
rightous7
Regular


Joined: 07 Mar 2010
Posts: 31


Report to Moderator

PostPosted: Sun Aug 26, 2012 1:36 pm    Post subject: oliver 129 haybine Reply to specific post Reply with quote

am looking at a 129 haybine about 4 hours from home , any one know how much they weigh or how wide they are ? trying to find the best way to get it home if i buy it . some large cities in between so do not think i can tow it with my pick up , maybe sideways on a goose neck ? thanks
 
Back to top
View user's profile
jordan hackman
Long Time User


Joined: 06 May 2011
Posts: 644


Report to Moderator

PostPosted: Sun Aug 26, 2012 6:04 pm    Post subject: Re: oliver 129 haybine Reply to specific post Reply with quote

i don't know alot about these and have only seen pictures of them but i do know for sure that it has a 9 foot cut so add in the the two or so inches of the right side and the two to four feet on the left side it gets pretty wide. so side ways on a goose neck is your safest and fastest way to move it. as i stated before i don't know much but it should weigh what any other 9ft haybine would weigh or less.
 
Back to top
View user's profile
dlauer
New User


Joined: 14 Jun 2012
Posts: 6


Report to Moderator

PostPosted: Mon Aug 27, 2012 2:29 pm    Post subject: Re: oliver 129 haybine Reply to specific post Reply with quote

I have a 129 and can measure if you would like.It is wider than a nh 489.U would have to put sideways on trailer and take tounge and pto off.The guards are the same as a gehl as agco wants way too much money for them.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters