Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

super 55


 
Post new topic    
View previous topic :: View next topic  
Author Message
P I Pete
Guest






Report to Moderator

PostPosted: Sun Sep 09, 2012 1:43 pm    Post subject: super 55 Reply to specific post Reply with quote

I bought a super 55 a couple mos. ago, engine was stuck, cracked sleeve and lots of rust 3 1/2" bore 1 hole kit is $250 easy choice, do all four. 3 5/8" or 3 3/4" if I go with the 3 3/4" will I gain any H.P with the larger bore? over the 3 5/8 Next question is will I have any trouble keeping it cool? It is a non pressure system. Also I am looking for a top link for 3 point and a 3 point 2 bottom plow in So Mn. thanks
 
Back to top
J. Schwiebert
Guest






Report to Moderator

PostPosted: Sun Sep 09, 2012 1:59 pm    Post subject: Re: super 55 Reply to specific post Reply with quote

It is your money. Get a good 3-5/8 kit, it will it the same displacement as a later 550
 
Back to top
RCP
Long Time User


Joined: 24 Feb 2000
Posts: 831


Report to Moderator

PostPosted: Sun Sep 09, 2012 3:02 pm    Post subject: Re: super 55 Reply to specific post Reply with quote

We run the 3-3/4 kit in our 77, same motor just 2 more holes. We have had no issues at all. However, I will say that if you do not do any thing else, then the HP will be very close between the 3-5/8 and the 3-3/4 kits.

Rich
 
Back to top
View user's profile
rrlund
Tractor Guru


Joined: 21 Dec 2006
Posts: 21251


Report to Moderator

PostPosted: Sun Sep 09, 2012 4:13 pm    Post subject: Re: super 55 Reply to specific post Reply with quote

Click the link and scroll down. Complete set of four 3 5/8th for $320. I just bought a set a few weeks ago. They've got the 3 3/4 too,I went with 3 5/8.
Korves

 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters