Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

MH 44 initial carb settings


 
Post new topic    
View previous topic :: View next topic  
Author Message
David G
Tractor Guru


Joined: 11 Jan 2008
Posts: 9027


Report to Moderator

PostPosted: Tue Sep 18, 2012 5:26 pm    Post subject: MH 44 initial carb settings Reply to specific post Reply with quote

What should I set the idle and power mixture initial settings at?
 
Back to top
View user's profile
miner09
Long Time User


Joined: 02 Dec 2009
Posts: 1297


Report to Moderator

PostPosted: Tue Sep 18, 2012 5:50 pm    Post subject: Re: MH 44 initial carb settings Reply to specific post Reply with quote

Set large screw 1 1/2 turns and small 1/4 to 1/2 turns. This will be close. You can fine tune from this. Sometimes the small screw has to be screwed all the way in. Depends on how clean the carb is.
 
Back to top
View user's profile
David G
Tractor Guru


Joined: 11 Jan 2008
Posts: 9027


Report to Moderator

PostPosted: Tue Sep 18, 2012 6:10 pm    Post subject: Re: MH 44 initial carb settings Reply to specific post Reply with quote

Thanks much, carb is fresh with kit and new throttle shaft.
 
Back to top
View user's profile
Bev McIntyre
New User


Joined: 21 Sep 2012
Posts: 2


Report to Moderator

PostPosted: Sun Sep 23, 2012 6:47 am    Post subject: Re: MH 44 initial carb settings Reply to specific post Reply with quote

I need point settings, plug gap and valve setting for a 44 massey harris 6 cyl. It have a bad miss
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Massey Harris & Massey Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters