Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CA motor in D-14 starter question


 
Post new topic    
View previous topic :: View next topic  
Author Message
Peter Hendrickson
Guest






Report to Moderator

PostPosted: Thu Sep 20, 2012 4:48 pm    Post subject: CA motor in D-14 starter question Reply to specific post Reply with quote

just bought a d-14 and they have a ca motor in it and the starter wont work (wont go in all the way), what flywheel should it have? obviously they put the wrong fly wheel in it but they cant tell me what one the used. any advise as to what to do?
Thanks Pete
 
Back to top
JMS/.MN
Tractor Guru


Joined: 05 Mar 2009
Posts: 7530


Report to Moderator

PostPosted: Thu Sep 20, 2012 6:39 pm    Post subject: Re: CA motor in D-14 starter question Reply to specific post Reply with quote

May not be the flywheel. Some starters don't swap between engines cuz the nose cone needs to be changed.
 
Back to top
View user's profile
Dick L
Tractor Guru


Joined: 01 Sep 1999
Posts: 9541
Location: Edon Ohio

Report to Moderator

PostPosted: Fri Sep 21, 2012 3:11 am    Post subject: Re: CA motor in D-14 starter question Reply to specific post Reply with quote

The starter and flywheel would have to be from the D 14. That is if that is your problem. The D 14 flywheel is a larger diameter than the CA flywheel.
 
Back to top
View user's profile
Butch(OH)
Tractor Expert


Joined: 19 Jun 2000
Posts: 1789


Report to Moderator

PostPosted: Fri Sep 21, 2012 6:41 am    Post subject: Re: CA motor in D-14 starter question Reply to specific post Reply with quote

Also was two differant D-14 ring gear tooth counts. I think the ring gear change came at same time as 6V to 12V change??
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters