|
This is the modern view of the Yesterday's Tractors Forums. Just login with your YT Userid and password to post. If you have trouble logging in, contact us by email to support at ytmag.com, or through the Reader Form, and we will get you going right away.
| View previous topic :: View next topic |
| Author |
Message |
MaxAllen(TX)
Guest
Report to Moderator
|
 Posted: Mon Sep 24, 2012 3:08 pm Post subject: Throttle Control Lever Repair |
  |
|
Hello all, I am trying to find some information on how to replace the little steel ball in the throttle control lever. Mine is totally worn down. I have seen some information on this before but haven"t been able to find any information in the archives. Any information would be appreciated. Thanks.
|
|
| Back to top |
|
 |
Bob Harvey
Tractor Guru
Joined: 18 Jan 2003
Posts: 4197
Report to Moderator
|
| Posted: Mon Sep 24, 2012 3:36 pm Post subject: Re: Throttle Control Lever Repair |
|
|
There is a 'kit' for that problem- maybe avilable here in "tractor parts". Allegedly, the ball can be 'rotated' for longer life. Would take a deft hand , a SHARP center punch/drift and some careful application with a mallet - NOT a BFH !
|
|
| Back to top |
|
|
Bruce (VA)
Tractor Guru
Joined: 24 Feb 2003
Posts: 11314
Location: Old Church VA
Report to Moderator
|
| Posted: Mon Sep 24, 2012 4:10 pm Post subject: Re: Throttle Control Lever Repair |
|
|
You will probably need to replace the plate as well.
50 Tips
|
|
| Back to top |
|
|
ASEguy
Tractor Expert
Joined: 19 Mar 2010
Posts: 1645
Report to Moderator
|
| Posted: Mon Sep 24, 2012 4:36 pm Post subject: Re: Throttle Control Lever Repair |
|
|
I replaced the plate on mine and rotated the ball. I preferred the feel of detents over the slide of a worn out plate.
|
|
| Back to top |
|
|
notjustair
Long Time User
Joined: 07 Jun 2010
Posts: 785
Location: NE Kansas
Report to Moderator
|
| Posted: Mon Sep 24, 2012 5:02 pm Post subject: Re: Throttle Control Lever Repair |
|
|
I went to the hardware store with the throttle lever in hand. Bought a ball bearing just a bit too big and gently knocked it in with a hammer. Squeezed the sides together a bit and I was done. Less than a buck.
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
|
|
Discount Prices for Parts! You can help support this extensive website by purchasing your tractor parts, manuals and merchandise from our [ Antique Tractor Store ] or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
|
YT Home
| Tractor Manuals
| Tractor Parts
| Forum Home
Copyright © 1997-2013 Yesterday's Tractor Co. - A Washington State Corporation
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
