Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

101 senior oil lines


 
Post new topic    
View previous topic :: View next topic  
Author Message
t martin
Regular


Joined: 22 Oct 2008
Posts: 141


Report to Moderator

PostPosted: Tue Sep 25, 2012 9:00 am    Post subject: 101 senior oil lines Reply to specific post Reply with quote

How are the oil lines routed to the oil filter on a 101 senior? Does the lower forward port in the block go to the bottom of the filter or the top? I am guessing the higher fitting in the block is pressure in and that the oil pressure guage gets tied into this. Looking for some insight here. Thanks
 
Back to top
View user's profile
David G
Tractor Guru


Joined: 11 Jan 2008
Posts: 8968


Report to Moderator

PostPosted: Tue Sep 25, 2012 6:03 pm    Post subject: Re: 101 senior oil lines Reply to specific post Reply with quote

Look back a few days about same question I posted on 44, bet it will answer your question.
 
Back to top
View user's profile
Mike in Mn.
Long Time User


Joined: 20 Dec 2009
Posts: 1034


Report to Moderator

PostPosted: Tue Sep 25, 2012 6:34 pm    Post subject: Re: 101 senior oil lines Reply to specific post Reply with quote


Does it have a Continental or Chrysler engine?? I have one with a Continental, I could have a look tomorrow and post.
 
Back to top
View user's profile
t martin
Regular


Joined: 22 Oct 2008
Posts: 141


Report to Moderator

PostPosted: Wed Sep 26, 2012 9:14 am    Post subject: Re: 101 senior oil lines Reply to specific post Reply with quote

It is a continental but I figured it out last night. I had the pressure guage hooked into the return line circuit, hence no oil pressure. I made up new lines and all is good. The 6 month project is finally making smoke.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Massey Harris & Massey Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters