Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

70 pony motor


 
Post new topic    
View previous topic :: View next topic  
Author Message
George Holbrook
New User


Joined: 03 Jan 2008
Posts: 10


Report to Moderator

PostPosted: Tue Sep 25, 2012 2:53 pm    Post subject: 70 pony motor Reply to specific post Reply with quote

Pony motor runs good the pinion engages as it should but its like the clutch just went out?
It"s been working fine..No slipage or engaging problems.The pinion just isn"t turning at all.
Its like the pinion drive has been disconnected from the clutch.Is there a shear pin in this drive somewhere?Help
Thanks George
 
Back to top
View user's profile
wijim
Long Time User


Joined: 20 Sep 2007
Posts: 1133
Location: neenah, wi

Report to Moderator

PostPosted: Tue Sep 25, 2012 5:09 pm    Post subject: Re: 70 pony motor Reply to specific post Reply with quote

Nope no shear pin, must be clutch went out. It might start turning the pinion again if the clutch plates get jambed in there, but it will turn all the time and you wont get it to engage.
 
Back to top
View user's profile
wijim
Long Time User


Joined: 20 Sep 2007
Posts: 1133
Location: neenah, wi

Report to Moderator

PostPosted: Tue Sep 25, 2012 5:12 pm    Post subject: Re: 70 pony motor Reply to specific post Reply with quote

Just had a thought, take the cover off the top of the pony trans and see if a pin didnt fall out of the linkage.
 
Back to top
View user's profile
LarrySTN
Long Time User


Joined: 27 Apr 2006
Posts: 784


Report to Moderator

PostPosted: Wed Sep 26, 2012 3:43 am    Post subject: Re: 70 pony motor Reply to specific post Reply with quote

IIRC, when my 70D did that, a spring had broken. I am certain I was able to make the repair without any major surgery on the tractor.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters