|
This is the modern view of the Yesterday's Tractors Forums. Just login with your YT Userid and password to post. If you have trouble logging in, contact us by email to support at ytmag.com, or through the Reader Form, and we will get you going right away.
| View previous topic :: View next topic |
| Author |
Message |
lee norris
Guest
Report to Moderator
|
 Posted: Wed Sep 26, 2012 7:30 am Post subject: 1948 Ford 8N Tractor |
  |
|
Dear Sirs:
I have a question. I am restoring the 1948 8N and need to know what 6V original generator and pulley diameter applies. I have the original 3 wire harness.
Your response would greatly be appreciated.
Thank you.
Lee
|
|
| Back to top |
|
 |
jackinok
Tractor Expert
Joined: 29 Apr 2010
Posts: 2976
Report to Moderator
|
| Posted: Wed Sep 26, 2012 8:19 am Post subject: Re: 1948 Ford 8N Tractor |
|
|
i do not have my part books here, but look in the parts section of this site.you could probably find what you need to know there, as far as the generator goes,maybe not the pulley diameter though. for some reason 3 1/2 " comes to mind but i could be wrong.
|
|
| Back to top |
|
|
Bob Purinton
Regular
Joined: 05 Oct 2010
Posts: 297
Report to Moderator
|
| Posted: Wed Sep 26, 2012 12:55 pm Post subject: Re: 1948 Ford 8N Tractor |
|
|
I went out and looked on my '48 8N and measured my 3 wire genny pulley. Jackinok is correct at 3.5 inches across the pulley.
|
|
| Back to top |
|
|
JMOR
Tractor Guru
Joined: 13 Aug 2007
Posts: 12795
Report to Moderator
|
| Posted: Wed Sep 26, 2012 1:49 pm Post subject: Re: 1948 Ford 8N Tractor |
|
|
| lee norris wrote: | (quoted from post at 11:30:57 09/26/12) Dear Sirs:
I have a question. I am restoring the 1948 8N and need to know what 6V original generator and pulley diameter applies. I have the original 3 wire harness.
Your response would greatly be appreciated.
Thank you.
Lee |
1948 is not enough info to identify which generator it would have left the factory with. It could have been 8N10000A (through serial #137684) or 8N1000B(serial #137685 thru #263843).
|
|
| Back to top |
|
|
Bob Purinton
Regular
Joined: 05 Oct 2010
Posts: 297
Report to Moderator
|
| Posted: Wed Sep 26, 2012 5:16 pm Post subject: Re: 1948 Ford 8N Tractor |
|
|
My 1948 8N is SN = 8N 131343
|
|
| Back to top |
|
|
JMOR
Tractor Guru
Joined: 13 Aug 2007
Posts: 12795
Report to Moderator
|
| Posted: Thu Sep 27, 2012 5:19 am Post subject: Re: 1948 Ford 8N Tractor |
|
|
| Bob Purinton wrote: | | (quoted from post at 21:16:32 09/26/12) My 1948 8N is SN = 8N 131343 |
Bob, so, if original, your generator should be 8N10000A, identified by a HI/LO adjustment screw on rear bearing plate, a 3rd brush which may have been removed as per an Oct, 1948 Service Bulletin, and it may have a barrel length (between the end plates) of 5 1/2 inches with some possibility of 6 1/8 inch length. Be interested in your response. Thanks.
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
|
|
Discount Prices for Parts! You can help support this extensive website by purchasing your tractor parts, manuals and merchandise from our [ Antique Tractor Store ] or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
|
YT Home
| Tractor Manuals
| Tractor Parts
| Forum Home
Copyright © 1997-2013 Yesterday's Tractor Co. - A Washington State Corporation
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
