Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

NAA oil gauge tube source


 
Post new topic    
View previous topic :: View next topic  
Author Message
Royse
Tractor Guru


Joined: 17 Jan 2011
Posts: 7535
Location: Michigan

Report to Moderator

PostPosted: Thu Sep 27, 2012 6:06 pm    Post subject: NAA oil gauge tube source Reply to specific post Reply with quote

Anyone have a source to get the oil gauge tube for a NAA?
It's essentially 1/8 inch steel "brake line", but I haven't been able to find it.
Book shows the part number as NAA-18676-A and/or NCA-99478-A if I'm reading it right.
I've patched mine for now, but if I could find a new one it would be nice.
 
Back to top
View user's profile
LeoinMI
Long Time User


Joined: 01 Sep 2009
Posts: 935


Report to Moderator

PostPosted: Thu Sep 27, 2012 7:05 pm    Post subject: Re: NAA oil gauge tube source Reply to specific post Reply with quote

Have you tried a local dealer? Grandville Tractor may be able to order one for you. I got alot of my parts for my NAA from them. Their phone number is 616-532-2347. ask for Bob or Dave in the Parts Department.
 
Back to top
View user's profile
CharnerL
Guest






Report to Moderator

PostPosted: Thu Sep 27, 2012 7:09 pm    Post subject: Re: NAA oil gauge tube source Reply to specific post Reply with quote

Any auto store has brake lines, same thing, and in different lengths. 3-5 $ each.
 
Back to top
Royse
Tractor Guru


Joined: 17 Jan 2011
Posts: 7535
Location: Michigan

Report to Moderator

PostPosted: Thu Sep 27, 2012 7:13 pm    Post subject: Re: NAA oil gauge tube source Reply to specific post Reply with quote

Thanks Leo, I've tried all the local parts houses, no one carries 1/8 inch.
I don't have a local CNH dealer.
I'll give Grandville a call and see what they say.
 
Back to top
View user's profile
Royse
Tractor Guru


Joined: 17 Jan 2011
Posts: 7535
Location: Michigan

Report to Moderator

PostPosted: Thu Sep 27, 2012 7:16 pm    Post subject: Re: NAA oil gauge tube source Reply to specific post Reply with quote

CharnerL wrote:
(quoted from post at 23:09:54 09/27/12) Any auto store has brake lines, same thing, and in different lengths. 3-5 $ each.

Thanks CharnerL, I've tried all the local parts houses. They have brake line,
but not that small. I might be able to adapt it down if necessary.
 
Back to top
View user's profile
Kurt-NEPA
Long Time User


Joined: 05 Mar 2009
Posts: 1022
Location: Tunkhannock, PA

Report to Moderator

PostPosted: Fri Sep 28, 2012 3:01 am    Post subject: Re: NAA oil gauge tube source Reply to specific post Reply with quote

I searched all over for an oil line for my 600. Even tried to find the adapters to use a larger line. No luck

The only place I found one was Messicks. I think that it must be made of gold, but it works.
 
Back to top
View user's profile
showcrop
Tractor Guru


Joined: 13 Dec 2000
Posts: 11024


Report to Moderator

PostPosted: Fri Sep 28, 2012 3:47 am    Post subject: Re: NAA oil gauge tube source Reply to specific post Reply with quote


I used the copper tubing kit from this site.
 
Back to top
View user's profile
Vito
Tractor Guru


Joined: 17 Aug 2004
Posts: 6423


Report to Moderator

PostPosted: Fri Sep 28, 2012 9:59 am    Post subject: Re: NAA oil gauge tube source Reply to specific post Reply with quote

If you are not going for correctness use a small plastic tube.

Vito
 
Back to top
View user's profile
souNdguy
Tractor Guru


Joined: 20 Aug 2002
Posts: 53468


Report to Moderator

PostPosted: Fri Sep 28, 2012 2:53 pm    Post subject: Re: NAA oil gauge tube source Reply to specific post Reply with quote

half of mine I replaced I use dthe copper 1/8 line.. the other half I used the plastic line. I like both for different applications.. would prefer steel over plastic or copper.. but they work...

auto stores have always had both in stock..
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters