Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

4430 stopped moving


 
Post new topic    
View previous topic :: View next topic  
Author Message
coreyc
Regular


Joined: 05 Mar 2009
Posts: 111


Report to Moderator

PostPosted: Thu Sep 27, 2012 6:16 pm    Post subject: 4430 stopped moving Reply to specific post Reply with quote

This 4430 quad range has been split at the bell housing and has had the clutches replaced next to the flywheel. Supposedly it has less than 200 hours since that was done. It wonít move now again. I am going to check pressures first but donít recall what they should be. I havenít had my hands on this tractor yet..just trying to get some ideas before I see it. Never really worked on a quad model only ps model
 
Back to top
View user's profile
Andrew F
Guest






Report to Moderator

PostPosted: Thu Sep 27, 2012 6:50 pm    Post subject: Re: 4430 stopped moving Reply to specific post Reply with quote

If I remember, trans system should be around 165 psi.
 
Back to top
tim s
Tractor Guru


Joined: 01 Nov 2008
Posts: 6888
Location: Somerset Ohio

Report to Moderator

PostPosted: Fri Sep 28, 2012 2:45 am    Post subject: Re: 4430 stopped moving Reply to specific post Reply with quote

If the clutch is not set up correctly it will not move,if the trans pump has failed and twisted off the shaft,or if the differential pinion shaft (spider gears) have failed it won"t move( locking the diff lock will prove the later),,just for a few ideas...
 
Back to top
View user's profile
Tx Jim
Tractor Guru


Joined: 14 Feb 1999
Posts: 16235
Location: Coyote Flats,Tx

Report to Moderator

PostPosted: Fri Sep 28, 2012 3:35 am    Post subject: Re: 4430 stopped moving Reply to specific post Reply with quote


Hyd hi-lo could have failed. Do you know if it's been tested in both speeds?
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters