Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

UTN progress update


 
Post new topic    
View previous topic :: View next topic  
Author Message
redgems
Long Time User


Joined: 11 Oct 2009
Posts: 576
Location: California

Report to Moderator

PostPosted: Thu Sep 27, 2012 7:06 pm    Post subject: UTN progress update Reply to specific post Reply with quote

Today 9/27/12 got the tranny shifting all five speeds, Got differential installed bull pinion shafts and bull gears in place.
Had problems with axles need to take them to large press for outer bearings and seal collors.
Got tranny top back from machine shop they installed new clutch shaft pin but forgot to rebush clutch handle.
Few pic's



 
Back to top
View user's profile
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 4111


Report to Moderator

PostPosted: Thu Sep 27, 2012 8:07 pm    Post subject: Re: UTN progress update Reply to specific post Reply with quote

You make me jealous..nice job.
 
Back to top
View user's profile
nys
Guest






Report to Moderator

PostPosted: Sat Sep 29, 2012 2:27 am    Post subject: Re: UTN progress update Reply to specific post Reply with quote

I'm so busy all I do is walk by my tractors and say hello wish I had some of your free time. Yup I'm jealous too.
 
Back to top
t.r.k.
Guest






Report to Moderator

PostPosted: Sat Sep 29, 2012 7:03 am    Post subject: Re: UTN progress update Reply to specific post Reply with quote

I don't see any assembly lube stains anywhere, and it bothers me.
 
Back to top
redgems
Long Time User


Joined: 11 Oct 2009
Posts: 576
Location: California

Report to Moderator

PostPosted: Sat Sep 29, 2012 7:58 am    Post subject: Re: UTN progress update Reply to specific post Reply with quote


Hi t.r.k.,
Yes using assembly lube . Matter fact Bob asked me to get another tube. WE have fingure prints all over that case. Ha Ha painter going to love us. Tony
 
Back to top
View user's profile
redgems
Long Time User


Joined: 11 Oct 2009
Posts: 576
Location: California

Report to Moderator

PostPosted: Sat Sep 29, 2012 8:12 am    Post subject: Re: UTN progress update Reply to specific post Reply with quote


I hear you NYS,
I am not retired yet so I was walking buy alot until I was able to set aside Thursdays for Bob and I to work on it.
I spend lot of time at night on net looking for parts service etc. Then I am up early on thursdays get what needs done on ranch then devote 8.30 to 5.30 to shop then back to ranch till about 7pm. Long day but fun. If I wait to retire I am afraid I will not have energy or money to do like I want. I am 66 3/4 of age and energy is getting to be a precious commodity.And I am worried about forgetting what I was doing last week Ha Ha
Tony
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters