Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

OT-Cub Z Turn Finished


 
Post new topic    
View previous topic :: View next topic  
Author Message
JCinKY
Long Time User


Joined: 01 Aug 2012
Posts: 757
Location: Glendale KY

Report to Moderator

PostPosted: Fri Sep 28, 2012 6:57 pm    Post subject: OT-Cub Z Turn Finished Reply to specific post Reply with quote

Posted a few weeks ago that I picked up a Cub RZT 50 with a blown motor. Had the alum block repaired at work, man those guys are good. Two new rods, oil pump shaft (I hate losing parts), quick valve job, and some oil and it runs like a top.

Not as much fun as the 8N but will be easier to mow around the the house. Happy tractoring.

-Jeff
 
Back to top
View user's profile
TheOldHokie
Tractor Guru


Joined: 08 Apr 2005
Posts: 6999
Location: Myersville, MD

Report to Moderator

PostPosted: Sat Sep 29, 2012 5:04 am    Post subject: Re: OT-Cub Z Turn Finished Reply to specific post Reply with quote

JCinKY wrote:
(quoted from post at 22:57:18 09/28/12) Posted a few weeks ago that I picked up a Cub RZT 50 with a blown motor. Had the alum block repaired at work, man those guys are good. Two new rods, oil pump shaft (I hate losing parts), quick valve job, and some oil and it runs like a top.

Not as much fun as the 8N but will be easier to mow around the the house. Happy tractoring.

-Jeff


The fun comes when the grass looks nicer and you are done quicker leaving you ensconced in your recliner watching the game with a beverage and chips on the table beside you Wink
 
Back to top
View user's profile Visit poster's website
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters