Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

case 504 weight


 
Post new topic    
View previous topic :: View next topic  
Author Message
Ohio Case
Regular


Joined: 16 Jan 2003
Posts: 264


Report to Moderator

PostPosted: Sun Sep 30, 2012 3:06 pm    Post subject: case 504 weight Reply to specific post Reply with quote

Does anyone know what the weight of a 504 is? It would have everything on it, looking to build/buy an engine stand and don't want to go too light.
 
Back to top
View user's profile
chuck machinist
Long Time User


Joined: 05 Jul 2011
Posts: 1139
Location: Chesapeake va

Report to Moderator

PostPosted: Sun Sep 30, 2012 4:07 pm    Post subject: Re: case 504 weight Reply to specific post Reply with quote

If you do not get any response tonite ,try the pullers forum,and don"t forget to try the {archives} I.E. 504. good luck chuck
 
Back to top
View user's profile
farmboyWI
Regular


Joined: 02 Jan 2011
Posts: 211


Report to Moderator

PostPosted: Sun Sep 30, 2012 5:53 pm    Post subject: Re: case 504 weight Reply to specific post Reply with quote

Just out of curiosity, when I disassembled my 1370ís 504, I weighed the bare block. That alone was 597lbs. Iím not real good at guessing weights but I would say the heads are 60-70lbs a piece, the crank another 130-150, pistons and rods probably 60-80, flywheel another 80-100. I bought a cheap Chinese made stand that was rated for 1000lbs for the 1290 engine that Iím working on and it seems overloaded with only (guessing again) 400lbs on it. Plus itís a real beast to turn over with that much weight on it. Hope this helps!
 
Back to top
View user's profile
Ohio Case
Regular


Joined: 16 Jan 2003
Posts: 264


Report to Moderator

PostPosted: Sun Sep 30, 2012 6:24 pm    Post subject: Re: case 504 weight Reply to specific post Reply with quote

I may have found a real deal, an engine stand made by IH used in the R&D dept. at the old harvester plant in Indiana
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters