Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

I60 govener linkage


 
Post new topic    
View previous topic :: View next topic  
Author Message
gary ronkar
Guest






Report to Moderator

PostPosted: Wed Oct 03, 2012 4:06 pm    Post subject: I60 govener linkage Reply to specific post Reply with quote

I have a 1966 I60 that has been sitting in parts for some time. I have rebuilt the engine and have it running, but I can't figure out how the govener linkage and throttle linkage all work. I have an old manual, but there is no description or pictures of the linkage. Only a description on how to adjust. I was hoping someone would have some photos or could direct me to a web page that would be helpful.
 
Back to top
DiyDave
Tractor Guru


Joined: 16 Nov 2007
Posts: 8853


Report to Moderator

PostPosted: Wed Oct 03, 2012 4:22 pm    Post subject: Re: I60 govener linkage Reply to specific post Reply with quote

Your best bet would be to get the AC shop manual. You need to know which engine you have. A 149 uses a round muffler, and a 160 uses an oval muffler. There will be a serial # on the rear left flange, on about a 45 degree angle, of the motor. If you know where the tractor serial# is, its about an inch in front of that #. Once you figure out which motor you have, you can still get the original shop manual from Agco, It'll either be a D-15 series 1 (149CID), or series 2(160 CID). If you want an Agco parts source, try Sandy Lake Equipment, a long time western PA Agco dealer, till agco cut them out recently, Brenda in parts is who to ask for!
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters