Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

TAP FOR AUXILLARY HYDRAULICS 3000


 
Post new topic    
View previous topic :: View next topic  
Author Message
ZANE
Tractor Guru


Joined: 10 Aug 1998
Posts: 10287


Report to Moderator

PostPosted: Wed Oct 03, 2012 6:13 pm    Post subject: TAP FOR AUXILLARY HYDRAULICS 3000 Reply to specific post Reply with quote

How can you tap into the hydraulics on a 3000 without the add on control valve where the adapter plate is located.
I know how to tap into the hydraulics on the Hundred series without the control valve by tapping and plugging the hole under the adapter palte and then drilling and tapping a hole in the adapter plate for the return line and using the test port for the pressure line. I've got that rigged on my 660. I need to do something like that on a 3000 three cylinder so I can operate a two spool valve on a FIL.

Thanks, Zane
 
Back to top
View user's profile
TheOldHokie
Tractor Guru


Joined: 08 Apr 2005
Posts: 7012
Location: Myersville, MD

Report to Moderator

PostPosted: Thu Oct 04, 2012 4:09 am    Post subject: Re: TAP FOR AUXILLARY HYDRAULICS 3000 Reply to specific post Reply with quote

ZANE wrote:
(quoted from post at 22:13:55 10/03/12) How can you tap into the hydraulics on a 3000 without the add on control valve where the adapter plate is located.
I know how to tap into the hydraulics on the Hundred series without the control valve by tapping and plugging the hole under the adapter palte and then drilling and tapping a hole in the adapter plate for the return line and using the test port for the pressure line. I've got that rigged on my 660. I need to do something like that on a 3000 three cylinder so I can operate a two spool valve on a FIL.

Thanks, Zane


Install one of the aftermarket remote port manifolds under the block off plate - part number is HV-5902 and sold here for $88.84. The manifold has an OUT port to your loader valve and IN port back to the three point valve. If your remote valve has power beyond the manifold also has a RETURN port direct to the sump. If your remote valve is a plain open center valve without power beyond the RETURN port on the manifold is not used - simply plug it

TOH




 
Back to top
View user's profile Visit poster's website
ZANE
Tractor Guru


Joined: 10 Aug 1998
Posts: 10287


Report to Moderator

PostPosted: Thu Oct 04, 2012 9:39 am    Post subject: Re: TAP FOR AUXILLARY HYDRAULICS 3000 Reply to specific post Reply with quote

Thanks Old. I'll look into it and see if I can figure it out.

Zane
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters