|
This is the modern view of the Yesterday's Tractors Forums. Just login with your YT Userid and password to post. If you have trouble logging in, contact us by email to support at ytmag.com, or through the Reader Form, and we will get you going right away.
| View previous topic :: View next topic |
| Author |
Message |
GlenT
Regular
Joined: 28 Oct 2007
Posts: 260
Report to Moderator
|
 Posted: Thu Oct 04, 2012 2:26 pm Post subject: 630 Clutch Bearing Washer F1395R |
  |
|
The JD parts catalog page 20-8 shows F1395R key 16, bearing washer, facing so that the bent in part hits the inner race of the bearing. The bent in part is 1/8 inch looking at the JD parts breakdown online. I Probably shouldn't question the parts Bible (catalog) but if the bearing washer was turned around, it would clear just fine, hold more grease for the bearing, and show a profile to the bearing as the Bearing Retainer, key 13, F1394R does. Any thoughts on which way the bearing washer should go?
Thanks
|
|
| Back to top |
|
 |
wijim
Long Time User
Joined: 20 Sep 2007
Posts: 905
Location: neenah, wi
Report to Moderator
|
| Posted: Thu Oct 04, 2012 3:26 pm Post subject: Re: 630 Clutch Bearing Washer F1395R |
|
|
I just went through that delema, so I went against the pic in the book and put it in away from bearing.
|
|
| Back to top |
|
|
GlenT
Regular
Joined: 28 Oct 2007
Posts: 260
Report to Moderator
|
| Posted: Fri Oct 05, 2012 6:18 am Post subject: Re: 630 Clutch Bearing Washer F1395R |
|
|
Thanks for the speedy reply. It makes sense to put it in the way you did.
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
|
|
Discount Prices for Parts! You can help support this extensive website by purchasing your tractor parts, manuals and merchandise from our [ Antique Tractor Store ] or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
|
YT Home
| Tractor Manuals
| Tractor Parts
| Forum Home
Copyright © 1997-2013 Yesterday's Tractor Co. - A Washington State Corporation
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
