Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Model 60 Draw Bars


 
Post new topic    
View previous topic :: View next topic  
Author Message
JT's RandR
Regular


Joined: 26 Jan 2012
Posts: 135
Location: Charleston, IL

Report to Moderator

PostPosted: Sat Oct 06, 2012 10:28 am    Post subject: Model 60 Draw Bars Reply to specific post Reply with quote

I was wondering what sizes of factor stock drawbars were available in a modle 60. Most of the draw bars I have seen were fairly long and had a bend in them. But I have seen one with straight short drawbar and I was wondering if there were different lenghts available for these tractors?
 
Back to top
View user's profile
buickanddeere
Tractor Guru


Joined: 31 May 2003
Posts: 26583
Location: in front of computer

Report to Moderator

PostPosted: Sat Oct 06, 2012 11:30 am    Post subject: Re: Model 60 Draw Bars Reply to specific post Reply with quote

Answer can be located here.

http://jdpc.deere.com/jdpc/servlet/com.deere.u90490.partscatalog.view.servlets.HomePageServlet_Alt
 
Back to top
View user's profile
bill mart
Tractor Expert


Joined: 16 Feb 2008
Posts: 2453


Report to Moderator

PostPosted: Sat Oct 06, 2012 11:34 am    Post subject: Re: Model 60 Draw Bars Reply to specific post Reply with quote

factory drawbar has two holes at the front end,allows you to adjust for length. Bill
 
Back to top
View user's profile
Mike Aylward
Tractor Guru


Joined: 24 Feb 1999
Posts: 4515


Report to Moderator

PostPosted: Sat Oct 06, 2012 1:55 pm    Post subject: Re: Model 60 Draw Bars Reply to specific post Reply with quote

I believe two different drawbars were available for the 60. The difference is in the length required for whether the tractor has a live pto or not. Mike
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters