Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Hesston Round Baler


 
Post new topic    
View previous topic :: View next topic  
Author Message
hildebrand40
New User


Joined: 05 Mar 2009
Posts: 2
Location: Stafford, KS

Report to Moderator

PostPosted: Mon Oct 08, 2012 6:51 pm    Post subject: Hesston Round Baler Reply to specific post Reply with quote

This message is a reply to an archived post by LAA on February 04, 2011 at 05:38:41.
The original subject was "Re: Hesston Round Baler".

Hello I just bought an 856A. I have not had any luck with the net wrap system. When I engage it. it runs for maybe a second and the monitor says check mesh. I open up the back and the mesh is cut and hanging off the backside of the unit. I thought it was a problem with to much force being required to turn the roll but I put some graphite on the skids and adjusted the cradle. The only other thing I can think of is maybe the proximity sensor is bad. Does anyone have any ideas for me?
 
Back to top
View user's profile
GLB in Kansas
New User


Joined: 03 Jun 2011
Posts: 15


Report to Moderator

PostPosted: Mon Oct 08, 2012 7:24 pm    Post subject: Re: Hesston Round Baler Reply to specific post Reply with quote

sometimes mine is a little temperamental, and I have to hit the start button 2 or 3 times to get it to catch. I have had some trouble also with the mesh count wheel on the left side of the mesh cover. It seemed to be too smooth and slipping on the roll, so I cut some shallow grooves in the wheel, and that seemed to help.

Your manual will tell you how to check the mesh in and mesh count sensors with your monitor. Best wishes.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters