Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

UTN rear wheel weights


 
Post new topic    
View previous topic :: View next topic  
Author Message
redgems
Long Time User


Joined: 11 Oct 2009
Posts: 562
Location: California

Report to Moderator

PostPosted: Mon Oct 08, 2012 8:29 pm    Post subject: UTN rear wheel weights Reply to specific post Reply with quote


Can anyone please identify rear wheel wt # 10A373 is it correct for a Ut.or UTN
Also one weight has #10027x below the #10A373 is there any difference?? They look the same.
Any information is much appreciated. Thanks,Tony
 
Back to top
View user's profile
MM diesel
Long Time User


Joined: 22 Oct 2009
Posts: 583


Report to Moderator

PostPosted: Tue Oct 09, 2012 8:10 am    Post subject: Re: UTN rear wheel weights Reply to specific post Reply with quote

This is one of the correct type centers for the weights.
I use 3/4" threaded rod on my tractors. 2 bolts or rods on each side will hold quite a few weights. There are 4 holes in each weight and each wheel center also has 4 holes. Another similar weight has part # UT518, but I think those only have 2 holes.

 
Back to top
View user's profile
MM diesel
Long Time User


Joined: 22 Oct 2009
Posts: 583


Report to Moderator

PostPosted: Tue Oct 09, 2012 8:19 am    Post subject: Re: UTN rear wheel weights Reply to specific post Reply with quote

Here is what the weights look like on the tractors.

Correction: the 10A373 weights will have 8 holes, and the UT518 weights have 4 holes. You can see a UT 518 weight on the restored tractor (1956 UB special lp) The back tractor is 1954 UB diesel.

 
Back to top
View user's profile
Heath72
Regular


Joined: 12 Dec 2009
Posts: 322


Report to Moderator

PostPosted: Tue Oct 09, 2012 8:24 am    Post subject: Re: UTN rear wheel weights Reply to specific post Reply with quote

Yes, the 10A373 weight is correct for a early fifties U. Those weights came out around 1949, and were the updated version of the UT518. They were used for many years.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters