Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

F 40 Pressure Plate


 
Post new topic    
View previous topic :: View next topic  
Author Message
miner09
Long Time User


Joined: 02 Dec 2009
Posts: 1360


Report to Moderator

PostPosted: Tue Oct 09, 2012 4:16 pm    Post subject: F 40 Pressure Plate Reply to specific post Reply with quote

Removed engine today on HC 40 I"m rebuilding and it had a different pressure plate. It has a ring for throw out bearing to run on (#1 picture). Is this an up grade from old type pressure plate or just another brand, and which one is best to use? Just not familiar with this type.


 
Back to top
View user's profile
samn40
Tractor Guru


Joined: 06 Jun 2010
Posts: 3759


Report to Moderator

PostPosted: Tue Oct 09, 2012 11:19 pm    Post subject: Re: F 40 Pressure Plate Reply to specific post Reply with quote

looks to me like that is a spacer so the later type bearing will work.
On our FE 35s the early bearing had a 'nose' on it so it would reach the fingers, this bearing is no longer available over here and a spacer is needed so the plain modern bearing will work.
Maybe someone on your side of the pond knows something else about it?
Sam
 
Back to top
View user's profile
John(UK)
Long Time User


Joined: 24 Oct 2007
Posts: 1176


Report to Moderator

PostPosted: Wed Oct 10, 2012 2:37 am    Post subject: Re: F 40 Pressure Plate Reply to specific post Reply with quote

The Clutches are basically the same, it is the settings of the Clutches that are different...John(UK)...fergusontractors@hotmai.com
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters