Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Super W6 rear axle seals


 
Post new topic    
View previous topic :: View next topic  
Author Message
SproutW
Regular


Joined: 16 Jun 2002
Posts: 431


Report to Moderator

PostPosted: Wed Oct 10, 2012 5:52 pm    Post subject: Super W6 rear axle seals Reply to specific post Reply with quote

Where do I find a source for rear axle seals? Are they a pain to install? Thanks.
 
Back to top
View user's profile
Wayne in MN
Long Time User


Joined: 30 Jul 2007
Posts: 1373


Report to Moderator

PostPosted: Wed Oct 10, 2012 6:39 pm    Post subject: Re: Super W6 rear axle seals Reply to specific post Reply with quote

Your local Case-IH dealer.
Or take them out & cross reference the number at NAPA.
 
Back to top
View user's profile
sflem849
Tractor Guru


Joined: 15 Jan 2007
Posts: 5844
Location: SE Wisconsin

Report to Moderator

PostPosted: Wed Oct 10, 2012 7:20 pm    Post subject: Re: Super W6 rear axle seals Reply to specific post Reply with quote

From what I have heard it is TERRIBLE to get the hubs off the axle. I'm sure the seals are fairly easy once you are in there. Probably the tough double leather jobs, but easier than getting the hub off.
 
Back to top
View user's profile
J.J. from Afton
Long Time User


Joined: 15 Jun 2007
Posts: 568
Location: Afton, MN

Report to Moderator

PostPosted: Wed Oct 10, 2012 8:28 pm    Post subject: Re: Super W6 rear axle seals Reply to specific post Reply with quote

As long as the castings are not stubborn its not bad. My 560W I had to use a T-puller and a torch on one of the cast centers it was damaged in the process, but it was also a W6 center on a 560, other one came right off by hand.


 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters