Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

1150 case


 
Post new topic    
View previous topic :: View next topic  
Author Message
Bill in Colo
Long Time User


Joined: 01 Oct 1999
Posts: 1039
Location: Rio Blanco,county Colorado

Report to Moderator

PostPosted: Thu Oct 18, 2012 4:04 pm    Post subject: 1150 case Reply to specific post Reply with quote

Need two slave cylinders for old 1150 case part# A 50361 they are available from case for $ 175 ea. Were available after market for $55. but can't find. Looking for help.
Thanks Bill
 
Back to top
View user's profile
AJ.
Long Time User


Joined: 20 Oct 2007
Posts: 793


Report to Moderator

PostPosted: Sat Oct 20, 2012 6:21 am    Post subject: Re: 1150 case Reply to specific post Reply with quote

Its a long time since I've seen an 1150 but seem to remember repairing the brake cylinders,as far as I can recall those cylinders were fairly standard Lockheed parts,7/8" if my memory is correct but I not 100% about the size,its easy to measure them,I used to get a repair kit from an auto parts shop going by the size rather than a part number, with the right size seals and a rub of a honing tool the machine would be back at work pronto,of course if the cylinder bore is too bad that would be no good but if the cylinders are ok they will be as good as new when you put new seals in,see what size you need and ask at your auto shop.
AJ
 
Back to top
View user's profile
Bill in Colo
Long Time User


Joined: 01 Oct 1999
Posts: 1039
Location: Rio Blanco,county Colorado

Report to Moderator

PostPosted: Sun Oct 21, 2012 6:26 pm    Post subject: Re: 1150 case Reply to specific post Reply with quote

Foung and old chev wheel cylinder kit that looks like it will work,have the worst one nearly honed enough, probably would work now.
thanks Bill
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters