Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

5 star puller


 
Post new topic    
View previous topic :: View next topic  
Author Message
mark fulmer
Guest






Report to Moderator

PostPosted: Wed Oct 24, 2012 2:25 pm    Post subject: 5 star puller Reply to specific post Reply with quote

help just bought my first M&M a5 star. had to have one after i saw art forrest pull the genarel. now comes the fun part. were to start .i want start with rear .i was told the stock rear will not hold up to div 4 7500. so any advice such as what gears axles needle bearings and were to get parts would be greatly appreciated thanks
 
Back to top
Jeff Gravert
Regular


Joined: 27 Jul 2008
Posts: 366


Report to Moderator

PostPosted: Thu Oct 25, 2012 3:36 am    Post subject: Re: 5 star puller Reply to specific post Reply with quote

What weight class and what division are you wanting to run? That will make alot of differences on how to go about your build. I have alot of engine parts as well as tractor and chassis parts. Division 4 at 4500 lbs is an awesome place to be but it costs alot to get there. Jeff @ Gravert Restoration 308-940-0255
 
Back to top
View user's profile
Murray Greenwood
Guest






Report to Moderator

PostPosted: Sat Oct 27, 2012 12:32 pm    Post subject: Re: 5 star puller Reply to specific post Reply with quote

Are you interested in purchasing a large cubic inch 5-star that has already been built?
 
Back to top
880
New User


Joined: 30 Oct 2012
Posts: 2


Report to Moderator

PostPosted: Tue Nov 13, 2012 6:40 pm    Post subject: Re: 5 star puller Reply to specific post Reply with quote

how many cubic inches?
how many hooks on motor?
will it fit m5?
how much money?
580-471-5122 ask for jack
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters