Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

4 3/8 pistons


 
Post new topic    
View previous topic :: View next topic  
Author Message
newby puller
New User


Joined: 26 Oct 2012
Posts: 15


Report to Moderator

PostPosted: Fri Oct 26, 2012 3:57 pm    Post subject: 4 3/8 pistons Reply to specific post Reply with quote

Want to bore m block to 4 3/8 where can I get some pistons and how much do they run thanks
 
Back to top
View user's profile
440
Guest






Report to Moderator

PostPosted: Fri Oct 26, 2012 6:25 pm    Post subject: Re: 4 3/8 pistons Reply to specific post Reply with quote

use chrysler 440 pistons, available everywhere and not expensive.
 
Back to top
newby puller
New User


Joined: 26 Oct 2012
Posts: 15


Report to Moderator

PostPosted: Sat Oct 27, 2012 1:19 am    Post subject: Re: 4 3/8 pistons Reply to specific post Reply with quote

Thanks do they fit stock rods on stock stroke
 
Back to top
View user's profile
High Octane
Regular


Joined: 27 Feb 2007
Posts: 356


Report to Moderator

PostPosted: Sat Oct 27, 2012 6:30 am    Post subject: Re: 4 3/8 pistons Reply to specific post Reply with quote

no, youd need longer rods or add a stroker crank. "cut n paste" a set of M rods to the length you need n run it. or, spend 800 or more on custom set that uses stock rods. Talk to Ray at Extreme tractor parts. He will make you anything you need. Also, you need a super m thru 450 block to run over 4.25, but not over 4.38 bore in em. Ms r good to 4.25 bore. good luck.
 
Back to top
View user's profile
Josh Blackburn
Long Time User


Joined: 28 Dec 2009
Posts: 552


Report to Moderator

PostPosted: Sat Oct 27, 2012 6:52 am    Post subject: Re: 4 3/8 pistons Reply to specific post Reply with quote

contact gary baker or murphys.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters