Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

80R3 Mower rebuild


 
Post new topic    
View previous topic :: View next topic  
Author Message
biggerred
Long Time User


Joined: 21 Jan 2000
Posts: 518


Report to Moderator

PostPosted: Wed Oct 31, 2012 5:20 pm    Post subject: 80R3 Mower rebuild Reply to specific post Reply with quote

Im replaceing the seals on the twin drive gearbox on my sickle mower. When putting the "towers" back on the main housing is there any gear timing issues to be aware of?
 
Back to top
View user's profile
Bob Bancroft
Tractor Guru


Joined: 05 Mar 2009
Posts: 3724
Location: Aurora NY

Report to Moderator

PostPosted: Wed Oct 31, 2012 10:00 pm    Post subject: Re: 80R3 Mower rebuild Reply to specific post Reply with quote

As I recall, just make sure the flywheels will be in phase with one another.
 
Back to top
View user's profile
biggerred
Long Time User


Joined: 21 Jan 2000
Posts: 518


Report to Moderator

PostPosted: Thu Nov 01, 2012 3:26 am    Post subject: Re: 80R3 Mower rebuild Reply to specific post Reply with quote

Thanks
 
Back to top
View user's profile
WEL
Regular


Joined: 05 Mar 2009
Posts: 47


Report to Moderator

PostPosted: Thu Nov 01, 2012 4:45 am    Post subject: Re: 80R3 Mower rebuild Reply to specific post Reply with quote

I am looking at an 80R3 sickle mower. Will it easily attach to a WD45? The owner said it came off of a WD but I can't see how it did without special brackets. Need advice. Thanks
 
Back to top
View user's profile
Skyhighballoon(MO)
Regular


Joined: 06 Jul 2007
Posts: 360


Report to Moderator

PostPosted: Thu Nov 01, 2012 6:03 am    Post subject: Re: 80R3 Mower rebuild Reply to specific post Reply with quote

An 80R3 is a 3 point mounted version that would go on any tractor that could accept a Category 1 implement.

A regular mounted 80 mower would have special brackets to mount to a WD/WD45, D17, D14/D15, etc. Each bracket would be special to each tractor except those that are alike (e.g. WD/WD45).

Mike
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters