Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Nuffield/ Fordson Major Parts interchangeability


 
Post new topic    
View previous topic :: View next topic  
Author Message
Abacus
New User


Joined: 06 Nov 2012
Posts: 1


Report to Moderator

PostPosted: Tue Nov 06, 2012 12:36 pm    Post subject: Nuffield/ Fordson Major Parts interchangeability Reply to specific post Reply with quote

Hi,
I have a Fordson Major and was wondering if the old Nuffield
hood and front end cone, say 46"-50" would fit a 57"-59"
Fordson Major? Any comments would be very helpful.
Thanks,
Lynn
 
Back to top
View user's profile
CNKS
Tractor Guru


Joined: 10 Mar 2002
Posts: 18059


Report to Moderator

PostPosted: Tue Nov 06, 2012 5:11 pm    Post subject: Re: Nuffield/ Fordson Major Parts interchangeability Reply to specific post Reply with quote

Ford forum is a better place for an answer.
 
Back to top
View user's profile
Robert Major
Long Time User


Joined: 02 Jun 2008
Posts: 864
Location: Manitoba , Canada

Report to Moderator

PostPosted: Tue Nov 06, 2012 6:15 pm    Post subject: Re: Nuffield/ Fordson Major Parts interchangeability Reply to specific post Reply with quote

Hi
They are totally different tractors why would you mess a great Fordson Major up putting tin on from a Nuffield It wasn"t a rip roaring success of a tractor L.O.L
Probably if the width and height was close a guy could make it work but not %100 sure.
Guys have been modifying Nuffield fenders to fit majors for years and they look totally wrong.The proper tin is around if you look in the right places.
If you havent figured it out yet I bleed ford blue, wheel orange, and grey L.O.L
Regards Robert
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Paint and Bodywork All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters