Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

4430 pistons


 
Post new topic    
View previous topic :: View next topic  
Author Message
Ken Henry
Regular


Joined: 25 Aug 2012
Posts: 24


Report to Moderator

PostPosted: Tue Nov 06, 2012 9:05 pm    Post subject: 4430 pistons Reply to specific post Reply with quote

Are there oversize pistons available for a 4430. I haven't been able to find any.
 
Back to top
View user's profile
tim s
Tractor Guru


Joined: 01 Nov 2008
Posts: 7360
Location: Somerset Ohio

Report to Moderator

PostPosted: Wed Nov 07, 2012 5:28 am    Post subject: Re: 4430 pistons Reply to specific post Reply with quote

What are your intentions?? There are some performance kits available....
 
Back to top
View user's profile
buickanddeere
Tractor Guru


Joined: 31 May 2003
Posts: 26211
Location: in front of computer

Report to Moderator

PostPosted: Wed Nov 07, 2012 11:27 am    Post subject: Re: 4430 pistons Reply to specific post Reply with quote

Don't try to over bore the old sleeves. They are likey rotted half way through with pin holes.
Sleeve and piston kit is reasonable in price.
 
Back to top
View user's profile
travis miranowski
Regular


Joined: 21 Oct 2012
Posts: 45


Report to Moderator

PostPosted: Wed Nov 07, 2012 8:24 pm    Post subject: Re: 4430 pistons Reply to specific post Reply with quote

Like buickanddeere said, New piston sleeve assemblies are in order. John Deere sells assemblies that you push the piston out just far enough to install the rod and install the piston, sleeve, and rod into the block at the same time. Reasonable price, probably $2000,00 for the out of frame kit extended from deere. Includes 6 piston liner kits, seals, gaskets, bearings, rod and cam bushings. Extra parts you would need are head bolts $300, and rod bolts $60.00
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters