Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

TD18A


 
Post new topic    
View previous topic :: View next topic  
Author Message
lyle niemi
Tractor Guru


Joined: 11 May 2011
Posts: 6987


Report to Moderator

PostPosted: Sun Nov 11, 2012 9:01 am    Post subject: TD18A Reply to specific post Reply with quote

H fellas, I thought I should post a pic of the old td18 I have been working on. Im gonna use it to run my sawmill. Im thinking t should have enough hp to do that little task. It had sat in a guys shop for over twenty years and he decided to get rid of it cause he didnt want to mess with it anymore so he just gave it to me. I got it running and give it a quick paint job.
 
Back to top
View user's profile
Dr. Walt
Tractor Expert


Joined: 06 Sep 2012
Posts: 1785
Location: Pahrump, Nevada

Report to Moderator

PostPosted: Mon Nov 12, 2012 9:13 pm    Post subject: Re: TD18A Reply to specific post Reply with quote

Lucky Dog!

Everything that I have gotten for "free" was JUNK
and would cost more to repair than if I went out and
bought it NEW.

ENJOY YOUR "NEW" TOY !
 
Back to top
View user's profile
to_many_irons
Regular


Joined: 01 Sep 2010
Posts: 299
Location: new brunswick

Report to Moderator

PostPosted: Thu Nov 15, 2012 5:53 pm    Post subject: Re: TD18A Reply to specific post Reply with quote

are you going to belt or a shaft to run the mill ?
 
Back to top
View user's profile
lyle niemi
Tractor Guru


Joined: 11 May 2011
Posts: 6987


Report to Moderator

PostPosted: Sat Nov 17, 2012 6:10 am    Post subject: Re: TD18A Reply to specific post Reply with quote

to_many_irons wrote:
(quoted from post at 02:53:29 11/16/12) are you going to belt or a shaft to run the mill ?
Im going to use belts, I just got the new shaft installed last night.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters