Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Backhoe Rubber Bumper Stop


 
Post new topic    
View previous topic :: View next topic  
Author Message
jred_82
New User


Joined: 30 Jun 2011
Posts: 10
Location: Champaign, IL

Report to Moderator

PostPosted: Sun Nov 11, 2012 4:16 pm    Post subject: Backhoe Rubber Bumper Stop Reply to specific post Reply with quote

Does anyone know where I can find some new rubber bumper stops? These go on either side of the backhoe boom to act as a stop for the side to side movement. Below is a picture of one of the existing ones which is pretty well shot as you can see. This is off a Wagner backhoe on a 1962 International 340U if matters.


 


Last edited by jred_82 on Sun Nov 11, 2012 4:17 pm; edited 2 times in total
Back to top
View user's profile
Archie McArdle
Guest






Report to Moderator

PostPosted: Sun Nov 11, 2012 5:59 pm    Post subject: Re: Backhoe Rubber Bumper Stop Reply to specific post Reply with quote

Late model Case's use a bumper like that . Take your sample in and compare....
 
Back to top
Dr. Walt
Tractor Expert


Joined: 06 Sep 2012
Posts: 1874
Location: Pahrump, Nevada

Report to Moderator

PostPosted: Mon Nov 12, 2012 8:47 pm    Post subject: Re: Backhoe Rubber Bumper Stop Reply to specific post Reply with quote

Wagner Equipment is now associated with Caterpillar
and AGCO .

You might try this:
http://www.wagnerequipment.com/parts-service/parts
 
Back to top
View user's profile
jred_82
New User


Joined: 30 Jun 2011
Posts: 10
Location: Champaign, IL

Report to Moderator

PostPosted: Sat Nov 24, 2012 9:47 am    Post subject: Re: Backhoe Rubber Bumper Stop Reply to specific post Reply with quote

Well I did not have any luck finding replacement bumper stops so I decided to make some. I ordered some round spring rubber from McMaster, cut it to length, and cut the centers out on the lathe. One solid piece would have probably been better, but considerably more expensive. If nothing else these are a good visual cue to stop rotating. I already ripped one of cylinders apart by over-rotating it.


 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters