Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

880 Gas Intake Manifold


 
Post new topic    
View previous topic :: View next topic  
Author Message
Del Anderson
Regular


Joined: 31 Jul 2008
Posts: 183


Report to Moderator

PostPosted: Sun Nov 11, 2012 5:54 pm    Post subject: 880 Gas Intake Manifold Reply to specific post Reply with quote

Does anybody no where you can get a gas intake manifold with better air flow for an Oliver 880 or 265 cu. in. motor. Thanks Del. PH 507-227-7062.
 
Back to top
View user's profile
chucksoliver77
Long Time User


Joined: 17 Sep 2009
Posts: 1351
Location: newton,n.j.

Report to Moderator

PostPosted: Sun Nov 11, 2012 7:22 pm    Post subject: Re: 880 Gas Intake Manifold Reply to specific post Reply with quote

Del, Extrude Hone 1800-367-1109 can make your stock intake flow really good. I had the one on my 77 done and works really good. It could barely rev to 3000 before and now goes right to 4000 rpms and makes good power. I'm using a USXcarb off a 1855. money well spent. chuck
 


Last edited by chucksoliver77 on Sun Nov 11, 2012 7:23 pm; edited 1 time in total
Back to top
View user's profile
J. Schwiebert
Guest






Report to Moderator

PostPosted: Mon Nov 12, 2012 3:52 am    Post subject: Re: 880 Gas Intake Manifold Reply to specific post Reply with quote

A 1650 gas manifold will also help if you have the stock 880 manifold
 
Back to top
Del Anderson
Regular


Joined: 31 Jul 2008
Posts: 183


Report to Moderator

PostPosted: Mon Nov 12, 2012 5:05 am    Post subject: Re: 880 Gas Intake Manifold Reply to specific post Reply with quote

J. We are using a 1650 head on the 880 block I think we will just clean out the 1650 intake as best as we can and try that for now. Thanks Del.
 
Back to top
View user's profile
ol.88
Guest






Report to Moderator

PostPosted: Tue Nov 13, 2012 10:29 am    Post subject: Re: 880 Gas Intake Manifold Reply to specific post Reply with quote

Murphys pulling parts has a nice one,you will like it..
 
Back to top
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters