Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Touching up Nason urethane


 
Post new topic    
View previous topic :: View next topic  
Author Message
RogerinMinn
Regular


Joined: 02 Nov 2011
Posts: 39
Location: Albert Lea, MN

Report to Moderator

PostPosted: Mon Nov 12, 2012 8:38 am    Post subject: Touching up Nason urethane Reply to specific post Reply with quote

Now that my tractor is painted I have a few small missed spots and a few spots where the paint is a little thin (if I ever do this again I will definitely light up my paint booth better). Do I need to scuff the areas with Scotch Brite and then touch it up or can I just spray it without scuffing? It will have been two weeks since it was painted. Nason Ful-thane over Nason epoxy primer.
 
Back to top
View user's profile
Stephen Newell
Tractor Expert


Joined: 11 Jun 2011
Posts: 1984


Report to Moderator

PostPosted: Mon Nov 12, 2012 10:28 am    Post subject: Re: Touching up Nason urethane Reply to specific post Reply with quote

I would scuff the paint to give the paint something to get a bite on.
 
Back to top
View user's profile
RogerinMinn
Regular


Joined: 02 Nov 2011
Posts: 39
Location: Albert Lea, MN

Report to Moderator

PostPosted: Mon Nov 12, 2012 10:59 am    Post subject: Re: Touching up Nason urethane Reply to specific post Reply with quote

Stephen Newell wrote:
(quoted from post at 11:28:23 11/12/12) I would scuff the paint to give the paint something to get a bite on.


Thank you. I kind of figured that would be the way to do it but wanted to be sure.
 
Back to top
View user's profile
DC3
New User


Joined: 06 Dec 2012
Posts: 1


Report to Moderator

PostPosted: Thu Dec 06, 2012 4:40 pm    Post subject: Re: Touching up Nason urethane Reply to specific post Reply with quote


tack cloth too
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Paint and Bodywork All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters