Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

allis wd45


 
Post new topic    
View previous topic :: View next topic  
Author Message
TomFGW
New User


Joined: 12 Nov 2012
Posts: 5


Report to Moderator

PostPosted: Mon Nov 12, 2012 6:56 pm    Post subject: allis wd45 Reply to specific post Reply with quote

I would like to put a allis 262 motor (the 262 is currently in a gleaner combine) into a wd45, I would like to know if i have to change the rails and will it bolt up to the 45 bell housing? I want to make a pulling tractor. THANKS TOM
 
Back to top
View user's profile
Midnightrider
Regular


Joined: 01 Jun 2009
Posts: 80


Report to Moderator

PostPosted: Mon Nov 12, 2012 8:47 pm    Post subject: Re: allis wd45 Reply to specific post Reply with quote


It will fit the rails and the bell housing. You will have to change the front out from your old engine because the Gleaner governor is different. It is a basic and simple swap.
 
Back to top
View user's profile
Kip-Utah
Long Time User


Joined: 22 Oct 2007
Posts: 568


Report to Moderator

PostPosted: Mon Nov 12, 2012 9:21 pm    Post subject: Re: allis wd45 Reply to specific post Reply with quote

Is your 45 a diesel? If so it's pretty straight forward. If it's a gasser then it's a tough conversion.
 
Back to top
View user's profile
TomFGW
New User


Joined: 12 Nov 2012
Posts: 5


Report to Moderator

PostPosted: Tue Nov 13, 2012 3:12 pm    Post subject: Re: allis wd45 Reply to specific post Reply with quote

thank you for the info i only have the motor right now just missed a diesel with a blown motor but if i understand this 262 motor will bolt up to a wd45 gas bell housing only issue is with the front end
 
Back to top
View user's profile
VicS
Tractor Expert


Joined: 12 Mar 2010
Posts: 3111


Report to Moderator

PostPosted: Tue Nov 13, 2012 5:41 pm    Post subject: Re: allis wd45 Reply to specific post Reply with quote

Kip is right, to put it into a Gas will be a challenge. Will be just as easy to put a V8 in it. But Allis uses adapter plates on their 6 cylinder engines, just like IH does. So you can put them into anything. But a WD 45 has a small bell housing and hence a small flywheel and clutch. A D 17 diesel would be a lot better, can put a 426 in them. Vic
 
Back to top
View user's profile
NCWC
Regular


Joined: 03 Jan 2010
Posts: 102


Report to Moderator

PostPosted: Thu Nov 15, 2012 5:22 pm    Post subject: Re: allis wd45 Reply to specific post Reply with quote

The 262 will fit. If you have a diesel tractor to begin with it goes right in no problems if dont you have to move the radiator and grill out to the end of the frame like the diesels are and make a longer hood or find a diesel hood. As far as the governers im not sure enought to say for sure if they are like the 226 engines you have to change some things over from the 45 block.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters