Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Cockshutt / Co-op Buda Governor


 
Post new topic    
View previous topic :: View next topic  
Author Message
Allis Fields
Regular


Joined: 26 Dec 2009
Posts: 222


Report to Moderator

PostPosted: Tue Nov 13, 2012 5:46 am    Post subject: Cockshutt / Co-op Buda Governor Reply to specific post Reply with quote

On a buda motor. what is the diference between a 6 ball and a 3 ball governor ?
 
Back to top
View user's profile
CoopCockhutt
Guest






Report to Moderator

PostPosted: Tue Nov 13, 2012 6:37 am    Post subject: Re: Cockshutt / Co-op Buda Governor Reply to specific post Reply with quote

The 3 ball governor has 3 balls in it. The 6 ball governor uses 6 balls.
 
Back to top
Allis Fields
Regular


Joined: 26 Dec 2009
Posts: 222


Report to Moderator

PostPosted: Tue Nov 13, 2012 1:36 pm    Post subject: Re: Cockshutt / Co-op Buda Governor Reply to specific post Reply with quote

yes but I was told the 6 ball one can take more rpms
 
Back to top
View user's profile
red 30
Guest






Report to Moderator

PostPosted: Tue Nov 13, 2012 2:18 pm    Post subject: Re: Cockshutt / Co-op Buda Governor Reply to specific post Reply with quote

6 ball came on 30s they have a larger gear so they turn slower . yes better for higher rpms.you also need housing that goes on the back of timing cover for correct height location .any more info call 716-308-5987
 
Back to top
blackangus
Regular


Joined: 27 Oct 2010
Posts: 27


Report to Moderator

PostPosted: Tue Nov 13, 2012 7:06 pm    Post subject: Re: Cockshutt / Co-op Buda Governor Reply to specific post Reply with quote

Had a ball governor in a E5 Coop threw a ball into cam gear not good ,went to a pierce weighted gov no problems and more responsive
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters