Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Farmall 350 Utility, Loader won't go up or down, no power st


 
Post new topic    
View previous topic :: View next topic  
Author Message
T.j lockhart
Guest






Report to Moderator

PostPosted: Fri Nov 16, 2012 3:56 pm    Post subject: Farmall 350 Utility, Loader won't go up or down, no power st Reply to specific post Reply with quote

I have a Farmall (IH)350 Utility tractor. It has no power steering and the loader won't raise , however the bucket tilts back and forth!
 
Back to top
Joshua Rod
Regular


Joined: 05 Mar 2012
Posts: 173


Report to Moderator

PostPosted: Fri Nov 16, 2012 6:33 pm    Post subject: Re: Farmall 350 Utility, Loader won't go up or down, no powe Reply to specific post Reply with quote

The first place I would look would be in your control valve, maybe your seals went bad for that lever.
 
Back to top
View user's profile
TJ lockhart
Guest






Report to Moderator

PostPosted: Fri Nov 16, 2012 6:52 pm    Post subject: Re: Farmall 350 Utility, Loader won't go up or down, no powe Reply to specific post Reply with quote

What about the power steering? Both aren't working, the loader up and the power steering? Are they both on the same circuit?
 
Back to top
Janicholson
Tractor Guru


Joined: 30 Jan 2004
Posts: 21401
Location: St. Cloud, MN

Report to Moderator

PostPosted: Fri Nov 16, 2012 7:07 pm    Post subject: Re: Farmall 350 Utility, Loader won't go up or down, no powe Reply to specific post Reply with quote

I would first check the single or double acting controls on each hydraulic lever. These are on the end opposite the lever. they are a roll pin through a milled flat. the roll pin must be either in the D position for two way action or S for single acting cylinder control. If these have been bent, it the little tin guard over the pin is distorted, they will cause issues. Let us know what you find. Jim
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters