Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

uni-motor


 
Post new topic    
View previous topic :: View next topic  
Author Message
ron tesch
Guest






Report to Moderator

PostPosted: Wed Nov 21, 2012 7:11 pm    Post subject: uni-motor Reply to specific post Reply with quote

I would like find cam for the 206 V-4 or whole motor for parts or someone to contact that would have the parts. call 605-886-8188
 
Back to top
817jdg
Regular


Joined: 05 Mar 2009
Posts: 96


Report to Moderator

PostPosted: Thu Nov 22, 2012 6:30 pm    Post subject: Re: uni-motor Reply to specific post Reply with quote

Hi. I dont have a cam or a motor. But I was alway curious what heads did they put on the v-4 motor. I am guessing that you have one? What is the head number if you get a chance to look Thanks for your time.
 
Back to top
View user's profile
t.r.k.
Guest






Report to Moderator

PostPosted: Thu Nov 22, 2012 7:17 pm    Post subject: Re: uni-motor Reply to specific post Reply with quote

Those V engines used 2 cams. You need to tell which one you need. (I don't have one, but I have worked on one of those engines.)

Also you need to tell if your engine is L head or OHV (overhead valve), I am pretty sure the timing marks or the keyways in the shafts will be different.

The L-heads used the same block as the ZB and the OHV engines used the same block (Or about the same block) as the 445.
 
Back to top
MMDEL
Regular


Joined: 29 Dec 2007
Posts: 493


Report to Moderator

PostPosted: Mon Nov 26, 2012 9:08 am    Post subject: Re: uni-motor Reply to specific post Reply with quote

I have those parts. Like trk says which cam Flat head or OHV???
MMDEL
815+456-2114
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters