Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Long/Oliver/Allis-Chalmers Round Tube Wide Front Rims!


 
Post new topic    
View previous topic :: View next topic  
Author Message
Fleetline
New User


Joined: 06 Oct 2012
Posts: 16


Report to Moderator

PostPosted: Thu Nov 22, 2012 5:14 pm    Post subject: Long/Oliver/Allis-Chalmers Round Tube Wide Front Rims! Reply to specific post Reply with quote

I was wondering if the front rims on a Long 360 with the round tube wide front had a metric measurement or if I could use a 6"x6" bolt pattern rim? The same wide front was used on some of the fiat built Oliver's and Allis'. Thanks!
 
Back to top
View user's profile
gatchelguy
Regular


Joined: 16 Apr 2011
Posts: 146


Report to Moderator

PostPosted: Fri Nov 23, 2012 6:16 am    Post subject: Re: Long/Oliver/Allis-Chalmers Round Tube Wide Front Rims! Reply to specific post Reply with quote

Any Ford pattern 6 bolt wheel will fit Long hubs. BUT it may have too much dish causing the tire to rub the axel.
 
Back to top
View user's profile
Bus Driver
Tractor Expert


Joined: 22 Nov 2000
Posts: 3238


Report to Moderator

PostPosted: Sat Nov 24, 2012 2:08 pm    Post subject: Re: Long/Oliver/Allis-Chalmers Round Tube Wide Front Rims! Reply to specific post Reply with quote

Once I had a front flat on my Long 360 a long distance from home. Preferred to get it home and then repair the flat. Farmer had three JD fronts (the later models with more than 2 cylinders) on his service truck and loaned me one. Bolted right on the Long, but vastly different offset, wider, larger diameter tire. Drove it home.
 
Back to top
View user's profile
Fleetline
New User


Joined: 06 Oct 2012
Posts: 16


Report to Moderator

PostPosted: Sat Nov 24, 2012 3:34 pm    Post subject: Re: Long/Oliver/Allis-Chalmers Round Tube Wide Front Rims! Reply to specific post Reply with quote

All the rims I'm finding are 6x6" bolt pattern, does that sound about right? Thanks!
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Lesser Known Classics All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters