Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Ford 101 landside replacement/worn frog


 
Post new topic    
View previous topic :: View next topic  
Author Message
Jake Collie
Regular


Joined: 10 Apr 2010
Posts: 369


Report to Moderator

PostPosted: Wed Nov 28, 2012 6:33 pm    Post subject: Ford 101 landside replacement/worn frog Reply to specific post Reply with quote

I just replaced the landsides on my new to me 101 plow. As you can see the leading edge of the new landsides stick down quite a ways from the bottom of the frog. I can cut up parts of the old landsides and weld them on to the frog to make the bottom edge of the new landsides and the bottom edge of the frog even, but do I need to do this? Will it cause me any problems leaving it the way it is? All ideas/suggestions are welcome. Thanks.


 
Back to top
View user's profile
flying belgian
Tractor Guru


Joined: 30 Aug 2008
Posts: 3967


Report to Moderator

PostPosted: Wed Nov 28, 2012 6:38 pm    Post subject: Re: Ford 101 landside replacement/worn frog Reply to specific post Reply with quote

I do not believe that will make any difference.
 
Back to top
View user's profile
DeltaRed
Tractor Guru


Joined: 25 Feb 2010
Posts: 13651
Location: Delta,colorado

Report to Moderator

PostPosted: Wed Nov 28, 2012 7:06 pm    Post subject: Re: Ford 101 landside replacement/worn frog Reply to specific post Reply with quote

Go plow,wont hurt a thing...
 
Back to top
View user's profile
JD Seller
Tractor Guru


Joined: 11 Mar 2009
Posts: 14971


Report to Moderator

PostPosted: Wed Nov 28, 2012 11:45 pm    Post subject: Re: Ford 101 landside replacement/worn frog Reply to specific post Reply with quote

That is how they all look. The land slide is what is supposed to wear. The frog looks good to me in the picture. Like Steve said, GO plow!!!
 
Back to top
View user's profile
Leroy
Tractor Guru


Joined: 09 Jan 1998
Posts: 15803
Location: Wapakoneta, Ohio

Report to Moderator

PostPosted: Thu Nov 29, 2012 5:55 am    Post subject: Re: Ford 101 landside replacement/worn frog Reply to specific post Reply with quote

That is the way the frof is made, it is NOT supposed to be as low as the bottom of the landside so that when the landsides wear you are not wearing on the frog. Have never seen a frog wear.
 
Back to top
View user's profile
donjr
Tractor Guru


Joined: 20 Nov 2011
Posts: 8469


Report to Moderator

PostPosted: Thu Nov 29, 2012 9:00 am    Post subject: Re: Ford 101 landside replacement/worn frog Reply to specific post Reply with quote

New landslides, new shins, just keep an eye on your shares and you're good to go for a lot of acres.....
 
Back to top
View user's profile
Jake Collie
Regular


Joined: 10 Apr 2010
Posts: 369


Report to Moderator

PostPosted: Thu Nov 29, 2012 10:01 am    Post subject: Re: Ford 101 landside replacement/worn frog Reply to specific post Reply with quote

OK, thanks for the replies. I guess I will leave it as is. There is a "wear pad" in front of the landsides that is affixed to the frog that has some wear. I may build it back up to the thickness of the new landsides and call it good. Unfortunately I will have to wait until spring to try it out.
 
Back to top
View user's profile
donjr
Tractor Guru


Joined: 20 Nov 2011
Posts: 8469


Report to Moderator

PostPosted: Fri Nov 30, 2012 9:05 pm    Post subject: Re: Ford 101 landside replacement/worn frog Reply to specific post Reply with quote

Jake- note that some landslides have a pad that bolts on near the rear as a wear point. Instead of replacing the entire landslide, you just replace the pad when it gets thin. Some wear on the landslide may happen as the pad wears thin, but the main landslide is still fine with minimal wear- the pad is all that needs to be replaced and is much cheaper than the full landslide.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters