Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

case 311 belt pulley


 
Post new topic    
View previous topic :: View next topic  
Author Message
Tristan in MN
Regular


Joined: 26 May 2012
Posts: 43


Report to Moderator

PostPosted: Sun Dec 02, 2012 6:27 pm    Post subject: case 311 belt pulley Reply to specific post Reply with quote

I have a 1956 311, it has a leak around the splined shaft coming out where the belt pully would be. a cover was made to keep stuff from wrapping around the shaft, i finally took the cover off today. There appears to be a seal around the shaft, I looked it up under CaseIH parts and all i could find is a smooth shaft with a tapered end where the belt pully attaches. Question: is this just a different design for the belt pully attachment and where can i find the seal for it? thanks
 
Back to top
View user's profile
C. Amick
Tractor Expert


Joined: 05 Mar 2009
Posts: 1581
Location: Wytheville, VA

Report to Moderator

PostPosted: Mon Dec 03, 2012 6:59 pm    Post subject: Re: case 311 belt pulley Reply to specific post Reply with quote

Stupid question, but have to checked the oil level in the reservoir to make sure you don't have too much oil in it? Not sure about the seal. If you can get a number off the seal, I'm sure Motion Industries or NAPA can probably match it up.
 
Back to top
View user's profile
Tristan in MN
Regular


Joined: 26 May 2012
Posts: 43


Report to Moderator

PostPosted: Mon Dec 03, 2012 7:34 pm    Post subject: Re: case 311 belt pulley Reply to specific post Reply with quote

Not a stupid question at all, actually the oil level in the torgue tube is low because all the oil seeps out at this level, i will have to dig into it one of these days. I found a bearing and seal supplier that is about 40 miles from here, hopefully they can match up what i need. thanks for the input.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters