|
This is the modern view of the Yesterday's Tractors Forums. Just login with your YT Userid and password to post. If you have trouble logging in, contact us by email to support at ytmag.com, or through the Reader Form, and we will get you going right away.
| View previous topic :: View next topic |
| Author |
Message |
jacksmad1
New User
Joined: 03 Dec 2012
Posts: 2
Report to Moderator
|
 Posted: Mon Dec 03, 2012 5:49 am Post subject: Belt for FEO-20 Ferguson Sickle Mower |
  |
|
I have an Ferguson FEO-20 sickle mower, but not the original belt or a parts manual. Does anyone know the size belt this mower requires? Length and width? I have an operators manual but it does not list the belt size.
|
|
| Back to top |
|
 |
Dick2
Tractor Guru
Joined: 11 Oct 2002
Posts: 7661
Report to Moderator
|
| Posted: Mon Dec 03, 2012 8:29 am Post subject: Re: Belt for FEO-20 Ferguson Sickle Mower |
|
|
Check with an Industrial Belt & Bearing distributor. They should be able to tell you how to measure for a new belt - and then sell you a much better belt than the original equipment belt for a lot less than a dealer will charge you for a belt.
|
|
| Back to top |
|
|
chuck41
Long Time User
Joined: 05 Mar 2009
Posts: 1149
Report to Moderator
|
| Posted: Mon Dec 03, 2012 8:51 am Post subject: Re: Belt for FEO-20 Ferguson Sickle Mower |
|
|
Jack, The FEO-20 was built narrow or wide. Narrow
for use with rear wheel in and wide for wheels
out(as for cultivating) The narrow is p/n 195671m1 (HC 92" outer)and wide is p/n 195672m1
(HC 105") Chuck
|
|
| Back to top |
|
|
jacksmad1
New User
Joined: 03 Dec 2012
Posts: 2
Report to Moderator
|
| Posted: Mon Dec 03, 2012 10:11 am Post subject: Re: Belt for FEO-20 Ferguson Sickle Mower |
|
|
| chuck41 wrote: | (quoted from post at 23:51:14 12/03/12) Jack, The FEO-20 was built narrow or wide. Narrow
for use with rear wheel in and wide for wheels
out(as for cultivating) The narrow is p/n 195671m1 (HC 92" outer)and wide is p/n 195672m1
(HC 105") Chuck |
Thanks Chuck!!
I had seen several references to the wide part number but had not ever seen the narrow one. Thanks for your help! 
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
|
|
Discount Prices for Parts! You can help support this extensive website by purchasing your tractor parts, manuals and merchandise from our [ Antique Tractor Store ] or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
|
YT Home
| Tractor Manuals
| Tractor Parts
| Forum Home
Copyright © 1997-2013 Yesterday's Tractor Co. - A Washington State Corporation
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
