Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

water pump for 1954 CA


 
Post new topic    
View previous topic :: View next topic  
Author Message
Mark in WV
Regular


Joined: 13 Dec 2003
Posts: 70


Report to Moderator

PostPosted: Tue Dec 04, 2012 5:36 pm    Post subject: water pump for 1954 CA Reply to specific post Reply with quote

I have a bad water pump for this CA...Is there anyone that rebuilds these, or just buy a new one?? Also, havent been able to remove the fan pulley and flange...Any suggestions??
 
Back to top
View user's profile
Zachary Hoyt
Tractor Guru


Joined: 07 Aug 2008
Posts: 4176


Report to Moderator

PostPosted: Tue Dec 04, 2012 5:59 pm    Post subject: Re: water pump for 1954 CA Reply to specific post Reply with quote

I've got a B pump that looks to be in good shape. I think it is the same but I am not sure. Complete with pulley for $25 if you're interested.
Zach
 
Back to top
View user's profile
Mark in WV
Regular


Joined: 13 Dec 2003
Posts: 70


Report to Moderator

PostPosted: Tue Dec 11, 2012 3:51 pm    Post subject: Re: water pump for 1954 CA Reply to specific post Reply with quote

I dont know for sure if I need one...This one began leaking...Just wondering if it can be rebuilt??? I tried to remove the pulley and still cant get it off.....
 
Back to top
View user's profile
Will Herring
Long Time User


Joined: 17 Jul 2005
Posts: 1219


Report to Moderator

PostPosted: Wed Dec 12, 2012 3:46 pm    Post subject: Re: water pump for 1954 CA Reply to specific post Reply with quote

I remember changing the water pump on my WD and the pulley/fan assembly was a pain in the rear to take off the old pump and put on the new one... I wound up finally using a wire brush (attached to a bench grinder style) to clean up the rust on the shaft, then the pulley comes off... Can't remember all that was to it, as it has been maybe 5 or 6 years now. Assume a CA may be similar. Post a picture of the assembly that won't come apart and I may be able to assist you more.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters